Logiquip SS32, Инструкция по использованию и установке

Страница: 6 / 24

SCRUB SINKS USE & INSTALLATION GUIDE
(800) 665-3760
6 |
IN-LINE FLOW SWITCH TIMER CONTROLLER (S0130-01) – SPECIFICATIONS, SWITCH RATING
AND WIRING DIAGRAM
NOTE: This feature (Fig 1) is available only on Infrared Activated Scrub Sinks
This is an explosion-proof brass flow switch, actuation setpoint 0 50 GPM (1 89 LPM), and calibrated for water at standard conditions It
is used for the accurate detection of excessive or insufficient flow rates
This unit was calibrated in a vertical position, with lead wires up Install the unit in the piping system, using standard pipe fitting
procedures Be sure to keep thread sealing compound out of unit Make sure that flow is in the proper direction - marked “IN” and
“OUT” on housing See wiring diagrams for electrical connections
CAUTION: See “Switch Ratings” before connecting power
CAUTION: Flow settings for this switch is normally calibrated using water @ +70°F on increasing flow Water-calibrated units are not
recommended for air/gas applications
SWITCH TIMER CONTROLLER MAINTENANCE
Accumulation of foreign debris should periodically be removed from these switches Occasional “wipe-down” cleaning when excessive
contamination is present is all that is normally required
TO CLEAN: Remove unit from system and disassemble as shown below Clean all parts, reassemble and reinstall unit
NOTE: 50 micron filtration is recommended
Fig 1 – In-Line Flow Timer Controller
Service Compatible liquids
Wetted materials Housing: brass; Piston: polysulfone; Spring: 316SS; O-Ring: Fluoroelastomer, Other: Epoxy.
Temperature Limits -20 to 225°F (-29 to 107°C).
Pressure Limits 1000 psig (68.9 bar).
Accuracy ±10% of set point.
Repeatability ±1%.
Switch Type* SPDT, 20 VA
Electrical Rating .17 A @ 120 VAC, .08 A @ 240 VAC, .13 A @ 120 VDC, .06 A @ 240 VDC.
Electrical Connection 18 AWG, 24" (60.96 cm), Polymeric lead wires.
Process Connection 1/4" female NPT.
Mounting Orientation Any position. Set points shown are based on vertical, inlet down position.
Required Filtration 50 microns or better.
Weight 0.66 lb (301 g).
Agency Approval
CE
*Switch Ratings Max Resistive Load
VA Volts Amps AC Amps DC
20
0-30 .4 .3
120 .17 .13
240 .08 .06
AA
CC
BB
Pin Connections for Units with
MS Receptacle
TTyyppiiccaall W Wiirriinngg DDiiaaggrraam m
Piston
Inlet Fitting
Housing
Spring
O-Ring
Service Compatible liquids
Wetted materials Housing: brass; Piston: polysulfone; Spring: 316SS; O-Ring: Fluoroelastomer, Other: Epoxy.
Temperature Limits -20 to 225°F (-29 to 107°C).
Pressure Limits 1000 psig (68.9 bar).
Accuracy ±10% of set point.
Repeatability ±1%.
Switch Type* SPDT, 20 VA
Electrical Rating .17 A @ 120 VAC, .08 A @ 240 VAC, .13 A @ 120 VDC, .06 A @ 240 VDC.
Electrical Connection 18 AWG, 24" (60.96 cm), Polymeric lead wires.
Process Connection 1/4" female NPT.
Mounting Orientation Any position. Set points shown are based on vertical, inlet down position.
Required Filtration 50 microns or better.
Weight 0.66 lb (301 g).
Agency Approval CE
*Switch Ratings Max Resistive Load
VA Volts Amps AC
Amps DC
20
0-30 .4 .3
120 .17 .13
240 .08 .06
AA
CC
BB
Pin Connections for Units with
MS Receptacle
TTyyppiiccaall W Wiirriinngg DDiiaaggrraam m
Piston
Inlet Fitting
Housing
Spring
O-Ring
Service Compatible liquids
Wetted materials Housing: brass; Piston: polysulfone; Spring: 316SS; O-Ring: Fluoroelastomer, Other: Epoxy.
Temperature Limits -20 to 225°F (-29 to 107°C).
Pressure Limits 1000 psig (68.9 bar).
Accuracy ±10% of set point.
Repeatability ±1%.
Switch Type* SPDT, 20 VA
Electrical Rating .17 A @ 120 VAC, .08 A @ 240 VAC, .13 A @ 120 VDC, .06 A @ 240 VDC.
Electrical Connection 18 AWG, 24" (60.96 cm), Polymeric lead wires.
Process Connection 1/4" female NPT.
Mounting Orientation Any position. Set points shown are based on vertical, inlet down position.
Required Filtration 50 microns or better.
Weight 0.66 lb (301 g).
Agency Approval CE
*Switch Ratings Max Resistive Load
VA Volts Amps AC Amps DC
20
0-30 .4 .3
120 .17 .13
240 .08 .06
AA
CC
BB
Pin Connections for Units with
MS Receptacle
TTyyppiiccaall W Wiirriinngg DDiiaaggrraam m
Piston
Inlet Fitting
Housing
Spring
O-Ring
*Switch Ratings Max Resistive Load