background image

Owner’s Manual (Toro GM4000 Series Snowblower) 

N14869                                                                                     1 -                                                                             November, 2004 

4

 
Operations Safety Continued: 

 

 

Do not allow any people or animals within 1000 
feet of the work area while operating this 
machine 

 

 

Thoroughly clear the work area of all foreign 
objects such as bottles, rocks, wire, etc. before 
starting shredder. 

 

 

When high pressure fluid escapes, it can be 
almost invisible, yet have enough pressure to 
penetrate the skin and enter the blood stream.  
Never attempt to use hands to search for 
suspected oil leak.  If injured by escaping fluid, 
consult a doctor at once!  Serious reaction or 
infection can occur if proper medical treatment 
is not obtained immediately. 

 

 

WARNING: 

 

 

Never operate the snowblower without guards, 
shields, plates or other safety precaution devices  

      in place.  Shields are for your protection, please  
      keep all shields in place. 
 

 

Do not operate on extremely steep slopes. 

 

 

Always remove snow by traveling in an up and 
down direction on slopes.  To avoid loss of 
control and to prevent overturn, never drive 
diagonally across the slope. 

 

 

Reduce speed when turning. 

 

 

Before servicing or adjusting the snowblower, or 
removing material from it, be sure to exercise 
the mandatory shut-down procedure. 

 

 

Be sure the auger has stopped completely before 
servicing. 

 

 

Be especially careful not to touch attachment 
parts which might be hot from operation.  
Allow such parts to cool before attempting to 
maintain, adjust, or service. 

 

 

DANGER:               

 

 

Never get off the machine while it is in motion, 
as entanglement can cause personal injury or 
death. 

 

 

Keep hands and feet out!  Do not step on or 
climb over the unit while machine is in 
operation, or engine is running.  Do not carry 
passengers. 

 
 
 
 
 
 
 
 
 
 

Содержание 601TR4000






































Отзывы: