Loctite 97007 Скачать руководство пользователя | Manualshive

Страница: 7 / 28

background image

7

1 Please observe the following

1.3 For Your Safety

For safe and successful operation of the unit, read these instructions completely. The
manufacturer cannot be held responsible for damage or injury of any kind because of misuse or
improper application or because of failure to observe safety instructions or warnings.

Be sure to retain this manual for future reference.

Request

the technical data sheet and the safety data sheet (acc. to the EC Directive 91/155/EC)

for the LOCTITE

®

-product used at

        Henkel Loctite Deutschland GmbH
    www.loctite.com         for US and Canada version of data sheets
        +49 89 92 68 11 67              for English version of data sheets;
        089-92 68 11 22                 for German version of data sheets.

FOLLOW UNCONDITIONALLY THE INSTRUCTIONS OF THESE DATA SHEETS!

If chemical products are not properly handled, damage to health can result!

Observe general safety regulations for the handling of chemicals!

Observe manufacturer’s instructions!
Request a safety data sheet for the LOCTITE-product used!

When working with pressurized air, wear protective glasses!

Damage to the power cord or the housing can result in contact with live electrical parts.

Check the power cord and the unit before each use.

If the power cord or the unit is damaged, do not operate!

Replace a damaged power cord with a new one.

The unit may be opened and repaired only by an authorized service personal.

Never fill the product directly into the
Product Reservoir!
The pneumatic safety devices would
become clogged and therefore
ineffective!
Insert only products packaged in
original LOCTITE containers!

«
...
5
6
7
8
9
...
»

Содержание 97007





























Отзывы:

Нет отзывов

Похожие инструкции для 97007

Бренд: Ugolini Страницы: 32

HTV8BLQ*1 Series

Бренд: Halsey Taylor Страницы: 9

Бренд: Oasis Страницы: 3

Бренд: Zass Страницы: 14

Бренд: GE Страницы: 60

Бренд: Hoshizaki Страницы: 51

Бренд: UFESA Страницы: 20

Бренд: Follett Страницы: 24

Бренд: Hendi Страницы: 16

Бренд: Siemens Страницы: 114

Бренд: DAN DRYER Страницы: 2

ATMOSPHERIC AWD-12 Series

Бренд: Hatco Страницы: 2

Бренд: Safetec Страницы: 5

Бренд: Delta Страницы: 11

Бренд: GINNY’S Страницы: 5

Бренд: Kimberly-Clark PROFESSIONAL Страницы: 33

Бренд: Ceasa Страницы: 33

Бренд: Bartscher Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды