Loctite 97007 Скачать руководство пользователя страница 21

Страница: 21 / 28

7 Troubleshooting

Type of Malfunction

Possible Causes

Corrections

Air bubbles in the product.

– Product reservoir is empty.

– Product hose not correctly connected.
– Dispensing valve not correctly

connected or defective.

– Product reservoir pressure is too high.

•

Refill product reservoir (see

section 5.2).

•

Connect product hose correctly.

•

Check the dispensing valve (see

instruction manual for dispensing
valve).

•

Lower pressure, longer dispensing

time.

Pressurized air escapes
between reservoir housing
and reservoir lid.

– Reservoir knob

not tightened.

– O-ring leaky.

•

Tighten the reservoir knob.

•

Grease or renew the O-ring.

Pressurized air escapes in
the reservoir housing.

– Punctured rupture disc.

– Depressurizing valve

open or

defective.

•

Replace the rupture disc (see

section 7.2).

•

Close the depressurizing valve or

change it.

Pressurized air escapes at
the product connection

– Union nut on the product connection

not tightened.

•

Carefully tighten the union nut.

Содержание 97007





























Результаты поиска

Содержание 97007

Отзывы:

Похожие инструкции для 97007

Бренды по названию

Популярные бренды

Loctite 97007, Руководство по эксплуатации

Результаты поиска

Содержание 97007

Отзывы:

Похожие инструкции для 97007

Бренды по названию

Популярные бренды