Lochinvar EcoSword LGC 160-210 G P CE Скачать руководство пользователя страница 87

Страница: 87 / 94

13.5

Declaration of conformity

EEC - Declaration of Conformity

Supplier:

hereby declares that the following products:

Product description:

Product models:

on the assumption that the installation instructions have been followed are complaint to:

Low Voltage Directive (LVD) - 2006/95/EG

- EN 60335-1:2012

Gas Appliance Regulations (GAR) - 2016/426

- EN 89:2015

- EN 60335-2-102:2006

Electromagnetic Compatibility Directive (EMC) - 2004/108/EG

- EN 55014-1:2007
- EN 55014-2:2015
- EN 61000-3-2:2014
- EN 61000-3-3:2013

Pressure Equipment Directive (PED) - 2014/68/EG

- Based on Art. 4, Sub 3. (PS < 10 bar, pressure vessel for non-hazardous fluids)

ECO Design Directive (ErP) - 2009/125/EG

- Commission regulation No. 814/2013 based on notices 2014/C - 207/03

Energy Labelling Directive - 2010/30/EG

- Commission regulation No. 812/2013

as stated in the EC type-examination report, 180100356, by KIWA Gastec Certification b.v., The Netherlands.

Product family name:

Company:

Date:

Lochinvar Limited
7 Lombard Way
The MXL Centre
Banbury - United Kingdom

Commercial Gas Fired Condensing Water Heater

LGSS 200-600, LGSS 200-780

Lochinvar Limited

November 1, 2018

E. van Driel
Managing Director

EcoSable

Signature:

0312582_EcoSword_V4.0, 03-05-2021

Содержание EcoSword LGC 160-210 G P CE































































































Результаты поиска

Содержание EcoSword LGC 160-210 G P CE

Отзывы:

Похожие инструкции для EcoSword LGC 160-210 G P CE

Бренды по названию

Популярные бренды

Lochinvar EcoSword LGC 160-210 G P CE, Инструкция по установке, пусконаладке, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание EcoSword LGC 160-210 G P CE

Отзывы:

Похожие инструкции для EcoSword LGC 160-210 G P CE

Бренды по названию

Популярные бренды