background image

43

        

Installation & Operation Manual

FOR YOUR SAFETY READ BEFORE OPERATING

WARNING:

 If  you do not follow these  instructions exactly,  a fire or explosion 

may result causing property damage, personal  injury, or loss of life. 

A.  This appliance does not have a pilot.  It is 

equipped with an ignition device which 
automatically lights the burner.  Do not try 
to light the  burner  by  hand. 

B.  BEFORE OPERATING smell all around 

the appliance area for gas.  Be sure to 
smell next to the floor because some gas 
is  heavier than air and will settle on the 
floor. 

WHAT TO DO IF YOU SMELL GAS 

 

Do not try to light any appliance. 

 

Do not touch any electric switch; do 
not use any phone in your building.  

 

Immediately call your gas supplier from a 
neighbor’s phone.  Follow the gas supplier’s 
instructions.  

 

If you cannot reach your gas supplier, call 
the fire  department. 

C.  Use only your hand to turn the gas control knob.  

Never use tools.  If the handle will not turn by 
hand, don’t try to repair it, call a qualified service 
technician.  Force or attempted repair may 
result in a fire or explosion. 

D.  Do not use this appliance if any part has been 

under water.  Immediately call a qualified 
service technician to inspect the applianc e and 
to replace any part of the control system and 
any gas control which has been under water. 

OPERATING INSTRUCTIONS 

1. 

STOP!

  Read the safety information 

above on this label. 

2.  Set the thermostat to lowes t setting. 

3.  Turn off all electric power to the 

applianc e. 

4.  This appliance is equipped with an 

ignition device which automatically lights 
the burner.  Do not try to light the burner 
by hand. 

5. Remove 

front 

door. 

6.  Turn gas shutoff valve counterclockwise 

to “OFF”.  Handle will be perpendicular to 
pipe.  Do not force.  

7.  Wait  five (5) minutes  to clear  out  any gas.   

If you then smell gas, 

STOP!

  Follow “B” 

in the safety information above this label.  
If you don’t smell gas, go to next step. 

8.  Turn gas shutoff valve clockwise to “ON”.  

Handle will be parallel to pipe. 

9. Install 

front 

door. 

10.  Turn on all electric power to applianc e. 

11. Set thermostat to desired setting. 

12. If the appliance will not operate, follow the 

instructions “To Turn Off Gas To Appliance” and 
call your service technician or gas supplier. 

TO TURN OFF GAS TO APPLIANCE 

1.  Set the thermostat to lowes t setting. 

2.  Turn off all electric power to the appliance 

if service is to be performed. 

3. Remove 

front 

door. 

4.  Turn gas shut off valve counterclockwise to 

“OFF”.  Handle will be perpendicular to pipe.   
Do not force.  

5. Install 

front 

door. 

L BL2 005 3 REV B 

Figure 9-2 Operating Instructions

9  

Start-up 

(continued)

 

 

Содержание Crest 2500 Series

































































Отзывы: