background image

                 

User’s Information Manual

1  

Maintenance schedule 

(continued)

7

Check appliance piping (gas and water)

1. Access the appliance and perform a gas 
 

leak inspection per steps 1 through 7 of the Operating 

 

Instructions on page 8. If gas odor or leak is detected, 

 

immediately shut down the boiler and call a qualified 

 service 

technician.

2.  Visually inspect for leaks around water piping. 

 

 

Also inspect the  circulators, relief valve, and fittings.  

 

Immediately call a qualified service technician to repair 

 any 

leaks.

 WARNING

Have leaks fixed at once by a qualified 
service technician.  Failure to comply could 
result in severe personal injury, death, or 
substantial property damage.

Operate relief valve

1.  Before proceeding, verify that the relief valve outlet has 
 

been piped to a safe place of discharge, avoiding any 

 

possibility of scalding from hot water.

 WARNING

To avoid water damage or scalding due 
to valve operation, a metal discharge 
line must be connected to the relief 
valve outlet and run to a safe place of 
disposal.  This discharge line must be 
installed by a qualified heating installer or 
service technician in accordance with the 
instructions in the Solution Installation 
and Service Manual.  The discharge line 
must be terminated so as to eliminate 
possibility of severe burns or property 
damage should the valve discharge.

2.  Read the boiler pressure/temperature gauge to make 
 

sure the system is pressurized.  Lift the relief valve 

 

top lever slightly, allowing water to relieve through 

 

the valve and discharge piping.

3.  If water flows freely, release the lever and allow the valve 
 

to seat.  Watch the end of the relief valve discharge pipe 

 

to ensure that the valve does not weep after the line has 

 

had time to drain.  If the valve weeps, lift the seat again to 

 

attempt to clean the valve seat.  If the valve continues to 

  weep afterwards, contact your qualified service 
 

technician to inspect the valve and system.

4.  If water does not flow from the valve when you lift the 
 

lever completely, the valve or discharge line may be 

 

blocked.  Immediately shut down the appliance.  Call 

 

your qualified service technician to inspect the appliance 

 and 

system. 

Shut appliance down (unless boiler is 

used for Domestic Water)

1.  Follow “To Turn Off Gas to Appliance” on page 9 of this 
 manual.

2.  Do not drain the system unless exposure to freezing 
 

temperatures will occur.

3.  Do not drain the system if it is filled with an antifreeze 
 solution.

4.  DO NOT shut down boilers used for domestic water 
 

heating, they must operate year-round.

Содержание 000 BTU/HR













Отзывы: