LK LD Series Скачать руководство пользователя страница 5

Страница: 5 / 48

- 5 -

Chapter.1. Noteworthy for installing an electric chain hoist

1.Checkup before installing

● There are several check points as follow;

1) Model 2) Voltage (3 phase, Voltage 220V, 380V, 440V. 460V)

3) Proof load 4) Trolley type 5) Lift

6) Push button type 7) Power cable length

8) Operating instruction 9) Any damage during moving and loading

2. Check point for particular cases

* Do no exposure to explosive places (explosion disposal hoists are available)

* Do not use or make an inquiry to the service center in a particular situation as

follows;

Under high temperature (over 40°C), Under low temperature (under -15°C),

in high humidity (over 85%), in the high elevated areas (over2000m)

In a basin(IP54)

* Especially to use in a low temperature, need to have extra capacities against

breakdown.

* lighting fixtures - keep 150LUX at the least from the driver's sit against any

accidents caused by mishandling.

* It produce around 71dB. For the quiet order, make inquiries at an office

* Control voltage...

3. Power

* Hold a power sauce failure or power transmission failure against a fire.

* Keep the Instruction for setup.

* Check the voltage and so on

4. Working rate

* Load time rate

* Safety index

5. Safety supervision

* Have safety wears such as gloves, boots, a crash helmet keep free from the

danger

6. Checking HOIST SPARE PART

1)CHAIN GAUGE (see the page 24 ,

2)OIL funnel (see the page27

LT,LD-TYPE HOIST is designed to stop operating hoist by the CLUTCH SLIP

action for avoid over loading. Therefore, when you use LT ,LD type of hoist,

need to observe the proof load.

Содержание LD Series

















































Результаты поиска

Содержание LD Series

Отзывы:

Бренды по названию

Популярные бренды

LK LD Series, Инструкция пользователя

Результаты поиска

Содержание LD Series

Отзывы:

Бренды по названию

Популярные бренды