background image

Form 998095
Rev. 000
10/17 

For technical assistance, parts, or repair, please contact...

888.956.0000

LIMITED WARRANTY

THIS WARRANTY (“WARRANTY”) SETS FORTH THE BRAND’S SOLE OBLIGATION AND PURCHASER’S EXCLUSIVE REMEDY FOR DEFECTIVE PRODUCT.

The Little Giant® Brand (the “Brand”) warrants that the products accompanied by this Warranty are free from defects in materials or workmanship that exist at the time of sale by the Brand and which occur  

or exist within the applicable warranty period identified below. Any distributor, sub-distributor, recipient, end-user and/or consumer agrees that by accepting the receipt of the products, the distributor,  

sub-distributor, recipient, end user and/or consumer expressly agrees to be bound by the terms of this Warranty.

I. Applicable Warranty Period

The products accompanied by this Warranty shall be covered by this Warranty for a period of 24 months 

from the date of original purchase by the consumer. In the absence of suitable proof of purchase date, 

the warranty period of this product will begin to run on the product's date of manufacture. 

II. Instructions Applicable to this Limited Warranty

1.  Consumers wishing to submit a warranty claim must return the products accompanied by this 

Warranty to the point of purchase for warranty consideration.

2.  Upon discovery of a potential defect, any personal injury, property damage or any other type of 

resulting damage, if applicable, shall be reasonably mitigated to the extent possible.

3.  At its discretion, the Brand may inspect products either at its facilities or in the field, and after 

determination of a warranty claim, will, at its option, repair or replace defective parts. Repaired or 

replaced parts will be returned freight prepaid by the Brand.

4.  This Warranty does not cover any labor or shipping charges. The Brand shall not be liable for any costs 

or charges attributable to any product testing, maintenance, installation, repair or removal, or for any 

tools, supplies, or equipment needed to install, repair, or remove any product.

III. Limitations Applicable to this Limited Warranty.

THIS WARRANTY DOES NOT APPLY TO ANY OF THE FOLLOWING:

1.  Brushes, impeller or cam on models with brush-type motors and/or flex-vane impellers.
2.  Any product that is not installed, applied, maintained and used in accordance with the Brand's 

published instructions, applicable codes, applicable ordinances and/or with generally accepted 

industry standards.

3.  Any product that has been subject to misuse, misapplication, neglect, alteration, accident, abuse, 

tampering, acts of God (including lightning), acts of terrorism, acts of war, fire, improper storage or 

installation, improper use, improper maintenance or repair, damage or casualty, or to an excess of 

the recommended maximums as set forth in the product instructions.

4.  Any product that is operated with any accessory, equipment, component, or part not specifically 

approved by the Brand. 

5.  Use of replacement parts not sold by the Brand, the unauthorized addition of non-Brand products 

to other Brand products, and the unauthorized alteration of Brand products.

6.  Products damaged by normal wear and tear, normal maintenance services and the parts used in 

connection with such service, or any other conditions beyond the control of the Brand.

7.  Any product that has been used for purposes other than those for which it was designed  

and manufactured.

8.  Any use of the product where installation instructions and/or instructions for use were not followed.
9.  Products connected to voltage other than indicated on nameplate.
10. Products where the pump was exposed to any of the following: sand, gravel, cement, grease, 

plaster, mud, tar, hydrocarbons, hydrocarbon derivatives (oil, gasoline, solvents, etc.) or other 

abrasive or corrosive substances.

11.  Products in which the pump has been used to pump or circulate anything other than fresh water 

at room temperature.

12.  Products in which the pump was allowed to operate dry (fluid supply cut off).
13.  Products in which the sealed motor housing has been opened or the product has been otherwise 

dismantled by customer.

14. Products in which the cord has been cut to a length of less than three feet.

This Warranty is the entire warranty authorized and offered by the Brand. There are no warranties or 

representations beyond those expressed in this document.

THIS WARRANTY AND REMEDY IS IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES INCLUDING 

WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE, 

WHICH ARE HEREBY SPECIFICALLY DISCLAIMED AND EXPRESSLY EXCLUDED. CORRECTION OF NON-

CONFORMITIES, IN THE MANNER AND FOR THE PERIOD OF TIME AS SET FORTH ABOVE, SHALL CONSTITUTE 

FULFILLMENT OF ALL LIABILITY OF THE BRAND TO THE PURCHASER WHETHER BASED ON CONTRACT, 

NEGLIGENCE, OR OTHERWISE.

THE BRAND SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES SUCH AS, 

BUT NOT LIMITED TO:

DAMAGE TO OR LOSS OF OTHER PROPERTY OR EQUIPMENT, LOSS OF USE OF EQUIPMENT, FACILITIES 

OR SERVICE, LOSS OF PROFIT OR SALES, COST OF PURCHASES OR REPLACEMENT GOODS, CLAIMS OF 

CUSTOMERS OF THE PURCHASER, FAILURE TO WARN AND/OR INSTRUCT, LOSS OF OTHER PRODUCTS, OR 

COSTS OF ENVIRONMENTAL REMEDIATION, OR DIMINUTION IN PROPERTY VALUE. THE REMEDIES OF THE 

PURCHASER SET FORTH HEREIN ARE EXCLUSIVE, AND THE LIABILITY OF THE BRAND SHALL NOT, EXCEPT 

AS EXPRESSLY PROVIDED HEREIN, EXCEED THE PRICE OF THE PRODUCTS UPON WHICH SUCH LIABILITY 

IS BASED. DAMAGES AS SET FORTH IN THIS PARAGRAPH SHALL BE REASONABLY MITIGATED TO THE 

EXTENT POSSIBLE. THIS PARAGRAPH SHALL ALSO APPLY TO ALL DAMAGES RESULTING FROM CONDITIONS 

SET FORTH IN SECTION III ABOVE AND (1) DEFECTS IN PRODUCT PROTOTYPES OR REPLACEMENT 

PART PROTOTYPES THAT HAVE NOT BEEN PUT INTO PRODUCTION, CIRCULATED AND SOLD BY THE 

BRAND, AND/OR (2) DEFECTS THAT WERE NOT FOUND AT THE TIME OF SALE DUE TO SCIENTIFIC AND 

TECHNOLOGICAL REASONS.

This Warranty gives you specific legal rights. You may have other rights, which vary according to the 

applicable laws and regulations. Where any term of this Warranty is prohibited by such laws, it shall 

be null and void, but the remainder of this Warranty shall remain in full force and effect.

DISCLAIMER:

 Any oral statements about the product made by the seller, the Brand, the 

representatives or any other parties, do not constitute warranties, shall not be relied upon by the 

user, and are not part of the contract for sale. Seller’s and the Brand’s only obligation, and buyer’s 

only remedy, shall be the replacement and/or repair by the Brand of the product as described above. 

Before using, the user shall determine the suitability of the product for his intended use, and user 

assumes all risk and liability whatsoever in connection therewith.

Содержание LG-MPA33

























Отзывы: