LiteOn EVO6000 Series Скачать руководство пользователя страница 22

Страница: 22 / 102

Chapter 4│Wiring

4.1 Wiring Safety

Danger



Turn off all the power to the equipment before wiring. Wiring during power on could cause
electrical shocks to personnel.



Allow only qualified personnel for installation, wiring, repairing and parts replacement.



Capacitors in the drive may still be charged for a short time after shutting off the power.
Wait for the amount of time specified on the drive before any maintenance.



Never touch input or output power cables. Do not connect any circuit to drive enclosure.

Warning



Properly connect the motor ground terminal. Contacts between the motor ground

terminal and motor enclosure could cause electrical shocks or a fire.



Ensure terminal screws are all tightened. Loose connection to the main circuit could cause

overheat or a fire.



Verify if the rated voltage of the drive matches the voltage of the incoming power supply

before applying power.



Perform all wiring as specified in the wiring diagrams provided when installing braking

unit. Failure to comply could result in drive, braking unit or resistor damage on fire.



Do not disconnect the motor from the drive while the drive is outputting voltage.



Do not use unshielded cable for control circuit wiring. Failure to comply could cause

abnormal operation of drive.



Use shielded twisted-pair cables and connect the shield to ground terminal of the drive.



Do not modify the drive circuits. Failure to comply could cause drive damage.



Ensure all connections are correct after connecting the drive with other devices.

Содержание EVO6000 Series







































































































Результаты поиска

Содержание EVO6000 Series

Отзывы:

Похожие инструкции для EVO6000 Series

Бренды по названию

Популярные бренды

LiteOn EVO6000 Series, Быстрый старт

Результаты поиска

Содержание EVO6000 Series

Отзывы:

Похожие инструкции для EVO6000 Series

Бренды по названию

Популярные бренды