Lister Petter LPP Series Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 52

background image

22

LPP PetRoL GeNset oPeRAtoRs' hANdbook

stARt the UNIt

PRe-stARt PRePARAtIoN

Before starting the generator, check for loose or missing parts and for any damage

which may have occurred during shipment or previous operation.

This generator must not be operated without all factory installed heat shields in

place.

1. Check the oil level and fuel.
2. Disconnect all electrical loads from the unit.
3. Turn the engine switch to “ON“ position (1).
4. Open fuel shut off valve (from “OFF” to

“ON“).

5. Adjust the choke of carburetor as

necessary.

Note:

Usually the choke is put in the position (1) of full

closing when cold starting, and will be opened

or half opened while warm starting.

WARNING

Petrol is very dangerous. Serious injury or death may

result from fire caused as a result of not adhearing to the

following:

1. Do not fill fuel tank with engine running.

2. Do not spill fuel while refilling tank (please use funnel

for refilling).

3. For 4-stroke engine, do not mix oil with petrol. For

2-stroke engine, please use oil-mixed petrol.

4.Follow all instructions and warnings in the engine

manual.

Failure to comply may cause the fuel tank to overheat and

result in personal injury from fire.

stARt the eNGINe

«
...
20
21
22
23
24
...
»

Содержание LPP Series





















































Отзывы:

Нет отзывов

Похожие инструкции для LPP Series

Бренд: Wavetek Страницы: 6

Бренд: DABBSSON Страницы: 37

Бренд: Campbell Hausfeld Страницы: 20

Бренд: Jabra Страницы: 2

HDG3000B Series

Бренд: Hantek Страницы: 22

Бренд: Xantrex Страницы: 36

LET'S GO PARTY 4 STUDIO

Бренд: N-Gear Страницы: 31

Бренд: Roberts Страницы: 24

Бренд: A-iPower Страницы: 112

Бренд: Ericsson Страницы: 34

Бренд: Tait Страницы: 120

Бренд: Panasonic Страницы: 7

Бренд: Panasonic Страницы: 18

Бренд: Panasonic Страницы: 32

Бренд: Panasonic Страницы: 42

Бренд: Panasonic Страницы: 33

DVD-LX9 - Portable DVD Player

Бренд: Panasonic Страницы: 49

Бренд: Panasonic Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды