Lippert SlimRack Скачать руководство пользователя

Страница: 13 / 24

Rev: 01.07.22

Page 13

CCD-0001459

Fault Code Table - Auto-Programmable Controllers

697096/700156

Flashes

Fault Type Description

Why?

What Should Be Done?

Green

Red

Minor

Park

brake

not set

(700156

only)

Parking brake (if applicable)

is not set.

Set parking brake (if applicable).

Ground signal is lost at

parking brake receptacle at

control box.

Check for continuity to ground on

wire plugged into parking brake

receptacle at control box.

Minor

Low

voltage

Incoming voltage to control

is below 12V DC. The room

will not move if the voltage

is 10.5V DC or below.

Start vehicle, generator, or make sure

the unit is plugged in to shore power.

Check 2-pin power connector at

the control box at BATT + and GND.

Consult manufacturer of unit charging

system for troubleshooting assistance.

Major

Motor 1

fault

Bad wire connection.

Refer to Technical Information Sheets:

Troubleshooting Control Box for

SlimRack Systems

82-S0533

. If necessary,

copy and paste or type the following

path into a browser; https://www.lci1.

com/slide-outs-/support-slimrack then

look for the specified document among

the listing.

Bad motor.

Major

Motor 2

fault

Bad wire connection.

Bad motor.

Minor

High

voltage

Supply voltage to control

box is 17V DC or greater.

Consult manufacturer of unit

charging system for troubleshooting

assistance.

Major

Stops

• Stops have not been set

• Stops were cleared

• Stops were improperly set

Stops need to be programmed

according to the programing

instructions in this document.

Major

Fuse

Motor fuse concern

Contact Lippert Representative

Major

Battery

Dropout

Battery dropped below

8.5V while extending or
retracting slides.

Charge battery, start vehicle,

generator, or make sure unit is

plugged into shore power.

Содержание SlimRack

























Результаты поиска

Содержание SlimRack

Отзывы:

Похожие инструкции для SlimRack

Бренды по названию

Популярные бренды

Lippert SlimRack, Руководство пользователя

Результаты поиска

Содержание SlimRack

Отзывы:

Похожие инструкции для SlimRack

Бренды по названию

Популярные бренды