Lippert SlimRack Скачать руководство пользователя

Страница: 12 / 24

Rev: 01.07.22

Page 12

CCD-0001459

Fault Code Table - Auto-Programmable Controllers

1510000236/366701 or 1510000276/366703

Flashes

Fault Type Description

Why?

What Should Be Done?

Green

Red

Minor

Park

brake

not set

Parking brake (if applicable)

is not set.

Set parking brake (if applicable).

Ground signal is lost at

parking brake receptacle at

control box.

Check for continuity to ground on

wire plugged into parking brake

receptacle at control box.

Minor

Low

voltage

Incoming voltage to control

is below 12V DC. The room

will not move if the voltage

is 10.5V DC or below.

Start vehicle, generator, or make sure

the unit is plugged in to shore power.

Check 2-pin power connector at

the control box at BATT + and GND.

Consult manufacturer of unit charging

system for troubleshooting assistance.

Major

Motor 1

fault

Bad wire connection.

Refer to Technical Information

Sheets: Troubleshooting Control Box

for SlimRack Systems

82-S0533

. If

necessary, copy and paste or type the

following path into a browser; https://

www.lci1.com/slide-outs-/support-

slimrack then look for the specified

document among the listing.

Bad motor.

Major

Motor 2

fault

Bad wire connection.

Bad motor.

Minor

High

voltage

Supply voltage to control

box is 17V DC or greater.

Consult manufacturer of

unit charging system for

troubleshooting assistance.

Содержание SlimRack

























Результаты поиска

Содержание SlimRack

Отзывы:

Похожие инструкции для SlimRack

Бренды по названию

Популярные бренды

Lippert SlimRack, Руководство пользователя

Результаты поиска

Содержание SlimRack

Отзывы:

Похожие инструкции для SlimRack

Бренды по названию

Популярные бренды