Linvatec Hall Series 4 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 40

background image

25

Trauma Drill

AO attachment will
not seat completely.

♦

Flat side of attachment is not
aligned with the arrow on the
collet.

♦

Align the flat side of attachment
with the arrow on the collet.

Trinkle attachment
will not seat
completely.

♦

Detent on attachment is not
aligned with the arrow on the
collet.

♦

Align detent of attachment with the
arrow on the collet.

Handpiece stalls
while driving.

♦

Direction control lever
possibly in the “SCREW”
position.

♦

Place the direction control lever in
the “FWD” or “REV” position.

Lack of handpiece
power.

♦

See Drill/Reamer troubleshooting
information on the previous pages.

Table 1: Troubleshooting Guide

Symptom

Possible Cause

Corrective Action

«
...
25
26
27
28
29
...
»

Содержание Hall Series 4









































Отзывы:

Нет отзывов

Похожие инструкции для Hall Series 4

Бренд: Keithley Страницы: 149

Бренд: Harken Страницы: 4

Бренд: BACtrack Страницы: 13

Бренд: TA Instruments Страницы: 35

Бренд: Danfoss Страницы: 106

Бренд: Hagie Страницы: 141

Бренд: h/p/cosmos Страницы: 81

Бренд: HABYS Страницы: 16

Бренд: Major tech Страницы: 12

Бренд: Safety 1st Страницы: 4

Бренд: Safety Engineering Страницы: 5

Chicken Coop Plan 3x5

Бренд: EASY COOPS Страницы: 21

Chicken Coop Plan 4x6

Бренд: EASY COOPS Страницы: 18

Chicken Coop Plan 8x10

Бренд: EASY COOPS Страницы: 18

Бренд: Zero88 Страницы: 26

Бренд: HAMOKI Страницы: 7

Бренд: H&S Страницы: 56

Бренд: U-Line Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды