![background image](http://html.mh-extra.com/html/linksys/befsr41-etherfast-cable-dsl-router/befsr41-etherfast-cable-dsl-router_user-manual_1924542049.webp)
43
Appendix A: Troubleshooting
Common Problems and Solutions
EtherFast Cable/DSL Router with 4-Port Switch
D. Make sure you use the right cable. Check to see if the Internet LED is solidly lit.
E. Make sure the cable connecting from your cable or DSL modem is connected to the Router’s Internet port.
Verify that the Status page of the Router’s Web-based Utility shows a valid IP address from your ISP.
F. Turn off the computer, Router, and cable/DSL modem. Wait 30 seconds, and then turn on the Router,
cable/DSL modem, and computer. Check the Status tab of the Router’s Web-based Utility to see if you get
an IP address.
5. I am not able to access the Router’s Web-based Utility Setup page.
A. Refer to “Problem #3, I want to test my Internet connection” to verify that your computer is properly
connected to the Router.
B. Refer to “Appendix C: Finding the MAC Address and IP Address for Your Ethernet Adapter” to verify that
your computer has an IP Address, Subnet Mask, Gateway, and DNS.
C. Set a static IP address on your system; refer to “Problem #2: I need to set a static IP address on a PC.”
D. Refer to “Problem #11: I need to remove the proxy settings or the dial-up pop-up window (for PPPoE
users).”
6. I can’t get my Virtual Private Network (VPN) to work through the Router.
Access the Router’s web interface by going to
http://192.168.1.1
or the IP address of the Router, and go to
the
Security
=>
VPN
tab. Make sure you have IPsec passthrough and/or PPTP passthrough enabled.
VPNs that use IPSec with the ESP (Encapsulation Security Payload known as protocol 50) authentication will
work fine. At least one IPSec session will work through the Router; however, simultaneous IPSec sessions
may be possible, depending on the specifics of your VPNs.
VPNs that use IPSec and AH (Authentication Header known as protocol 51) are incompatible with the Router.
AH has limitations due to occasional incompatibility with the NAT standard.
Change the IP address for the Router to another subnet to avoid a conflict between the VPN IP address and
your local IP address. For example, if your VPN server assigns an IP address 192.168.1.X (X is a number from
1 to 254) and your local LAN IP address is 192.168.1.X (X is the same number used in the VPN IP address), the
Router will have difficulties routing information to the right location. If you change the Router’s IP address to
192.168.2.1, that should solve the problem. Change the Router’s IP address through the Basic Setup tab of
the Web-based Utility. If you assigned a static IP address to any computer or network device on the network,
you need to change its IP address accordingly to 192.168.2.Y (Y being any number from 1 to 254). Note that
each IP address must be unique within the network.
Your VPN may require port 500/UDP packets to be passed to the computer that is connecting to the IPSec
server. Refer to “Problem #8, I need to set up online game hosting or use other Internet applications” for
details. Check the Linksys website at
www.linksys.com/international
for more information.
Содержание BEFSR41 - EtherFast Cable/DSL Router
Страница 73: ...67 Appendix H Regulatory Information and Safety EtherFast Cable DSL Router with 4 Port Switch ...
Страница 74: ...68 Appendix H Regulatory Information and Safety EtherFast Cable DSL Router with 4 Port Switch ...
Страница 75: ...69 Appendix H Regulatory Information and Safety EtherFast Cable DSL Router with 4 Port Switch ...