background image

35

Troubleshooting

System completely dead

1.  No power from transformer. Check voltage at AE-100 transformer 

terminals.

2.  Verify that terminal blocks are fi rmly plugged into circuit board.

Buzz on speaker

1.  Check for 16 volt AC power shorted to wiring conduit.
2.  Check for telephone line shorted to ground.

3

.  Verify that telephone wires are twisted pair.

4.  Verify that the AE-100 is connected to earth ground.
5.  Check 16 VAC voltage at AE-100 transformer terminals.

Buzz on telephone line

1.  Disconnect 16 VAC wires from terminal strip, if buzz goes away, 

one side of the transformer wires is grounded.

2.  Check all connections for any shorts to ground.

System will not answer an incoming call

1.  Automatic telephone answer disabled.
2.  AE-100 telephone line trouble.

Keypad will not activate a relay

1.  Entry code is not assigned.
2.  Keypad may be in lockout from too many incorrect attempts. Wait 

90 seconds for lockout to clear and try again.

Resident’s Telephone does not ring when a visitor 
calls

1.  Resident’s Telephone Number programmed incorrectly.
2.  Check AE-100 telephone line.

3

.  Call resident from another line or cell phone to determine if the 

resident’s telephone is working.

Linear Limited Warranty

This Linear product is warranted against defects in material and 
workmanship for twenty-four (24) months. This warranty extends only 
to wholesale customers who buy direct from Linear or through Linear’s 
normal distribution channels. Linear does not warrant this product to 
consumers. Consumers should inquire from their selling dealer as to 
the nature of the dealer’s warranty, if any. 

There are no obligations 

or liabilities on the part of Linear LLC for consequential damages 
arising out of or in connection with use or performance of this 
product or other indirect damages with respect to loss of property, 
revenue, or profi t, or cost of removal, installation, or reinstallation.

 

All implied warranties, including implied warranties for merchantability 
and implied warranties for fi tness, are valid only until the warranty expires. 

This Linear LLC Warranty is in lieu of all other warranties express 
or implied.

All products returned for warranty service require a Return Product 
Authorization Number (RPA#). Contact Linear Technical Services at 
1-800-421-1587 for an RPA# and other important details.

FCC Notice

Changes or modifi cations not expressly described in this manual or 
approved by the manufacturer could void the user’s authority to operate 
the equipment.
This equipment has been tested and found to comply with the limits for 
a Class B digital device, pursuant to Part 15 of the FCC Rules. These 
limits are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses 
and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not 
occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

 

Increase the separation between the equipment and receiver.

 

Connect the equipment into an outlet on a circuit different from that 

 

to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

 

Содержание ACCESS AE-100 Guide





































Отзывы: