background image

FL

OW T

YPE luxur

y COOLER

 

13

figure

  13 C

figure

  13 D

figure

  13 E

16. TEMPERATURE AND ADJUSTMENT :

TThe temperature of the cooled beverage is controlled by a mechanical thermostat in 

temperature range of 2 °C to 8 °C. The thermostat has a numerical scale of 1-7.

 WARNING:

    

If you are using the cooler to cool non-alcoholic beverages, set the thermostat 

knob to 5 at the most, otherwise, there is a risk of the beverage freezing in the cooler‘s tubing 

and damaging the device.

15.2   Speed Fitting Removal: 

Hold the grey ring tight against the body of 

the speed fitting and pull out the hose.

figure

  13 B

 WARNING:

   

If you do not hold the grey ring but pull at the hose, the speed fitting will cut 

even deeper into the hose.

 WARNING:

  

 Hoses must not be pressurised during removal.

15.  HOW TO WORK WITH SPEED FITTINGS:

15.1   Speed Fitting Installation: 

Grasp the speed fitting and insert the hose all 

the way inside the speed fitting body (ca. 20 

mm). The end of the hose must be straight so 

that it plugs fully into the coupling. If the hose 

will not go in, moisten the end of the hose. 

figure

  13 A

 0 = OFF

 1 = MAX. BEVERAGE   

TEMPERATURE (8°C)

7  =  MIN.  BEVERAGE                                                                                                            

TEMPERATURE(2°C)

Содержание KONTAKT 55





















Отзывы: