Lincoln SP-100T Скачать руководство пользователя | Manualshive

Страница: 9 / 35

background image

A-2

INSTALLATION

SP-100T

A-2

Read entire installation section before starting
installation.

SAFETY PRECAUTIONS

IDENTIFY AND LOCATE
COMPONENTS

If you have not already done so, unpack the SP-100T
from its carton and remove all packing material
around the SP-100T. Remove the following loose
items from the carton (see Figure A.1):

1. SP-100T

2. Gun and cable assembly

(1)

3. Literature and miscellaneous including:

a) This operating manual

b) 6 extra .023"-.025” (0.6 mm) contact tips

c) Hex key wrench for removal of drive roll.

4. 10 ft (3.0 m) work cable.

5. Work clamp.

6. 2Lb. spool of .025” (0.6 mm)Super Arc

L-56 MIG wire.

7. Handshield with filter plate and lens.

8. Instructional video.

9. Adjustable mixed-Gas Regulator & Hose.

For available options and accessories refer to the
Accessories Section of this manual.

1)

As shipped from the factory, the SP-100T gun liner
is ready to feed .023” (0.6 mm) -.035 (0.9 mm) wire.
The contact tip is sized for .023”-.025” (0.6 mm) wire .

ELECTRIC SHOCK can kill.

• Only qualified personnel should perform

this installation.

• Only personnel that have read and under-

stood the SP-100T Operating Manual
should install and operate this equipment.

• Machine must be plugged into a receptacle

which is grounded per any national, local
or other applicable electrical codes.

• The SP-100T power switch is to be in the

OFF (“O”) position when installing work
cable and gun and when connecting power
cord to input power.

WARNING

FIGURE A.1

SP-10

0T

1

2

3

4

6

7

8

9

5

«
...
7
8
9
10
11
...
»

Содержание SP-100T




































Отзывы:

Нет отзывов

Похожие инструкции для SP-100T

Бренд: CAME Страницы: 16

Бренд: CAME Страницы: 2

Бренд: Eco Страницы: 2

Бренд: Magmaweld Страницы: 8

AZ8350 - Cd Radio Cass Recorder

Бренд: Magnavox Страницы: 18

Бренд: Magmate Страницы: 20

Бренд: GBR Systems Страницы: 161

ACUSTICA H series

Бренд: RCF Страницы: 10

Бренд: EAW Страницы: 2

Бренд: Rainbow Страницы: 26

Exubera Pro UC EV9333-50

Бренд: Everpure Страницы: 2

Бренд: Sandstrom Страницы: 32

Esprit 738 EXPRESS

Бренд: Paradox Страницы: 36

Бренд: Migatronic Страницы: 28

Бренд: R&TTE Страницы: 6

Бренд: Omnitronic Страницы: 28

Бренд: Magnavox Страницы: 24

Бренд: YMGI Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды