Lincoln SP-100T страница 22 Скачать руководство пользователя

Страница: 22 / 35

C-2

ACCESSORIES

C-2

INNERSHIELD (FCAW)
CONVERSION

Several changes are needed to convert the unit for
operation with the Innershield (FCAW) process. The
K549-1 Innershield Kit include

’

s all the necessary

accessories for this conversion and is provided for this
purpose. The following conversions should be made
using the contents of this kit:

1. Change the output polarity to DC(

–

). See

“

Work

Cable Installation

”

in Installation section for details.

2. Install proper drive roll for the wire size selected.

See

“

Changing Drive Roll

”

in Maintenance section

for details.

3. Install the proper gun liner and tip for the wire size

selected. See

“

Component Replacement

”

Maintenance section for details.

4. Remove gas nozzle (if installed) and install gasless

nozzle. To remove, simply unscrew.

5. Load wire into machine and thread into gun and

cable per

“

Welding Wire Loading

”

section.

REPLACEMENT PARTS

Complete Gun and Cable Assembly

(K530-5)

Contact Tip .025” (0.6 mm)

KP2039-1

Contact Tip .030” (0.8 mm)

KP2039-2

Contact Tip .035” (0.9 mm)

KP2039-3

Contact Tip-Tapered .025” (0.6 mm)

KP2052-1

Contact Tip-Tapered .030” (0.8 mm)

KP2052-2

Contact Tip-Tapered .035” (0.9 mm)

KP2052-3

Liner .035/.045” (0.9/1.2 mm)

KP1937-1

Gas Diffuser

KP2040-1

Gas Nozzle

KP1938-1

Gas Nozzle-Tip Recessed 3/8” (9.5 mm)
Opening I.D.

KP1942-1

Gas Nozzle-Tip Recessed 1/2” (12.7 mm)
Opening I.D.

KP1942-2

Gas Nozzle-Tip Recessed 5/8” (15.9 mm)
Opening I.D.

KP1942-3

Spot Welding Nozzle

KP1956-1

Gasless Nozzle (Innershield Only)

KP1939-1

SP-100T

Содержание SP-100T




































Результаты поиска

Содержание SP-100T

Отзывы:

Похожие инструкции для SP-100T

Бренды по названию

Популярные бренды

Lincoln SP-100T, Руководство оператора

Результаты поиска

Содержание SP-100T

Отзывы:

Похожие инструкции для SP-100T

Бренды по названию

Популярные бренды