Lincoln 2009 MKZ Скачать руководство пользователя страница 153 | Manualshive

Страница: 153 / 293

background image

anchors is 280 mm (11 inches) center to center. A child seat with rigid
LATCH attachments cannot be installed at the center seating position.
LATCH compatible child seats (with attachments on belt webbing) can
only be used at this seating position provided that the child seat
manufacturer’s instructions permit use with the anchor spacing stated.
Do not attach a child seat to any lower anchor if an adjacent child seat is
attached to that anchor.

WARNING:

The standardized spacing for LATCH lower anchors

is 280 mm (11 inches) center to center. Do not use LATCH

lower anchors for the center seating position unless the child seat
manufacturer’s instructions permit and specify using anchors spaced at
least as far apart as those in this vehicle.

If you install a child seat with rigid LATCH attachments, and have
attached the top tether strap to the proper top tether anchor, do not
tighten the tether strap enough to lift the child seat off the vehicle seat
cushion when the child is seated in it. Keep the tether strap just snug
without lifting the front of the child seat. Keeping the child seat just
touching the vehicle seat gives the best protection in a severe crash.

Each time you use the safety seat, check that the seat is properly
attached to the lower anchors and tether anchor, if applicable. Tug the
child seat from side to side and forward and back where it is secured to
the vehicle. The seat should move less than one inch when you do this
for a proper installation.

If the safety seat is not anchored properly, the risk of a child being
injured in a crash greatly increases.

Combining safety belt and LATCH lower anchors for attaching
child safety seats

When used in combination, either the safety belt or the LATCH lower
anchors may be attached first, provided a proper installation is achieved.
Attach the tether strap afterward, if included with the child seat. Refer
to

Recommendations for attaching safety restraints for children

in

this chapter.

Attaching child safety seats with tether straps

Many forward-facing child safety seats include a tether strap which
extends from the back of the child safety seat and hooks to an anchoring
point called the top tether anchor. Tether straps are available as an
accessory for many older safety seats. Contact the manufacturer of your

2009 MKZ

(378)

Owners Guide, 2nd Printing
USA

(fus)

Seating and Safety Restraints

152

«
...
151
152
153
154
155
...
»

Содержание 2009 MKZ






































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 MKZ

Бренд: GATmatic Страницы: 13

Бренд: Ford Страницы: 22

Бренд: Cadillac Страницы: 518

Бренд: Opel Страницы: 141

Бренд: Phonocar Страницы: 2

Бренд: Subaru Страницы: 21

Бренд: hc-cargo Страницы: 60

Xplore Pro II SxS

Бренд: Marlon Страницы: 15

Бренд: Jeep Страницы: 380

Бренд: v.link Страницы: 21

Бренд: MAcarbon Страницы: 3

Бренд: Anker Technology Страницы: 8

Бренд: v.link Страницы: 19

Бренд: Needit Страницы: 2

KIT ParkingSensor 814

Бренд: Gemini Страницы: 6

Бренд: Pet Gear Страницы: 4

IGNIS 2022 Series

Бренд: Suzuki Страницы: 570

1500 CLASSIC 2020

Бренд: RAM Страницы: 360

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды