Lincoln Foodservice 1300 SERIES Скачать руководство пользователя

Страница: 9 / 20

CounterTop - 1300 Series Ops Manual

COUNTERTOP MOUNTING INSTRUCTIONS

Position the oven on the countertop and carefully mark the position of the rear legs. Remove the oven from the

countertop and position the mounting rings so that the large (center) hole is where the legs of the oven were

marked. Mark the position of the two small holes and remove the mounting rings. Install per instruction 1 or 2

below.

1. When installing on a heavy stainless steel countertop, use the four #10-32 x 3/8” machine screws. Use a .159”

diameter drill (#21) and drill through the countertop. Use a 10-32 tap through the holes. Using a screwdriver,

mount the rings in position. Set the oven on the countertop so that the rear legs are in the larger holes in the

mounting ring.

2. When installing on a plywood or composition board countertop, use the four #10 x ½” sheet metal screws. Use

a .169” diameter drill (#18) and drill at least ½” into the countertop. Using a screwdriver, mount the rings in

position. Set the oven on the countertop so that the rear legs are in the large holes in the mounting rings.

REAR

FRONT

Leg location for

Impinger

Countertop Oven

Содержание 1300 SERIES





















Результаты поиска

Содержание 1300 SERIES

Отзывы:

Похожие инструкции для 1300 SERIES

Бренды по названию

Популярные бренды

Lincoln Foodservice 1300 SERIES, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 1300 SERIES

Отзывы:

Похожие инструкции для 1300 SERIES

Бренды по названию

Популярные бренды