Lincoln Electric RED-D-ARC IM648-B Скачать руководство пользователя | Manualshive

Страница: 24 / 37

background image

PYTHON

E-1

TROUBLESHOOTING

E-1

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your
Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

CAUTION

This Troubleshooting Guide is provided to
help you locate and repair possible machine
malfunctions. Simply follow the three-step
procedure listed below.

Step 1. LOCATE PROBLEM (SYMPTOM).

Look under the column labeled

“

PROBLEM

(SYMPTOMS)

”

. This column describes

possible symptoms that the machine may
exhibit. Find the listing that best describes
the symptom that the machine is exhibiting.

Step 2. POSSIBLE CAUSE.

The second column labeled

“

POSSIBLE

CAUSE

”

lists the obvious external possibili-

ties that may contribute to the machine
symptom.

Step 3. RECOMMENDED COURSE OF
ACTION

This column provides a course of action for
the Possible Cause, generally it states to
contact you local Lincoln Authorized Field
Service Facility.

If you do not understand or are unable to
perform the Recommended Course of
Action safely, contact you local Lincoln
Authorized Field Service Facility.

HOW TO USE TROUBLESHOOTING GUIDE

Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel.
Unauthorized repairs performed on this equipment may result in danger to the technician and
machine operator and will invalidate your factory warranty. For your safety and to avoid
Electrical Shock, please observe all safety notes and precautions detailed throughout this
manual.

__________________________________________________________________________

WARNING

ELECTRIC SHOCK CAN KILL.

•

Turn off machine at the disconnect

switch on the front of the machine and
remove main power supply connec-
tions before doing any troubleshooting.

----------------------------------------------------------------------------

WARNING

«
...
22
23
24
25
26
...
»

Содержание RED-D-ARC IM648-B






































Отзывы:

Нет отзывов

Похожие инструкции для RED-D-ARC IM648-B

Бренд: KEF Страницы: 10

Interlogix 60-875 Simon

Бренд: GE Страницы: 40

Бренд: GE Security Страницы: 2

Бренд: iDance Страницы: 10

Бренд: ID Tech Страницы: 10

Бренд: Vahle Страницы: 40

Бренд: Vacron Страницы: 2

MCX-A10 - MusicCAST Network Audio Player

Бренд: Yamaha Страницы: 56

Soundmaster 138

Бренд: SOUNDMASTER Страницы: 1

Бренд: Bose Страницы: 44

Бренд: NEC Страницы: 16

SAPPHIRE COMPACT 309150001

Бренд: Hygood Страницы: 6

Бренд: Majorcom: Страницы: 15

MY LIFTER BASIC LIFTER

Бренд: Garage Smart Страницы: 31

Бренд: Gabarron Страницы: 16

NX-108E - Security NetworX NX-4 System

Бренд: GE Страницы: 20

CoolBloC C34 DN 32

Бренд: PAW Страницы: 24

STAGE-4 ROKKER XXR Custom

Бренд: J&M Corporation Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды