Lincoln Electric RED-D-ARC IM648-B Скачать руководство пользователя | Manualshive

Страница: 22 / 37

background image

PYTHON

D-1

MAINTENANCE

D-1

INPUT FILTER CAPACITOR
DISCHARGE PROCEDURE

1. Turn off input power or disconnect input power

lines.

2. Remove the 5/16" hex head screws from the side

and top of the machine and remove wrap-around
machine cover.

3. Be careful not to make contact with the capacitor

terminals that are located on the top and bottom of
the Power Board on the right side of the machine.

4. Obtain a high resistance and high wattage resistor

(25-1000 ohms and 25 watts minimum). This resis-
tor is not supplied with machine. NEVER USE A
SHORTING STRAP FOR THIS PROCEDURE.

5. Locate the two capacitor terminals (large hex head

cap screws) on the Power P.C. Board shown in
Figure D.1.

6. Use electrically insulated gloves and insulated pli-

ers. Hold body of the resistor and connect resistor
leads across the two capacitor terminals. Hold
resistor in place for 10 seconds. DO NOT TOUCH
CAPACITOR TERMINALS WITH YOUR BARE
HANDS.

7. Repeat discharge procedure for the other capaci-

tor .

8. Check voltage across terminals of all capacitors

with a DC voltmeter. Polarity of capacitor terminals
is marked on PC board above terminals. Voltage
should be zero. If any voltage remains, repeat this
capacitor discharge procedure.

ELECTRIC SHOCK

can kill.

•

Have an electrician install and service

this equipment.

•

Turn the input power off at the fuse

box before working on equipment.

•

Do not touch electrically hot parts.

•

Prior to Performing preventative main-

tenance, perform the following capaci-
tor discharge procedure to avoid elec-
tric shock.

---------------------------------------------------------------------

WARNING

CAPACITOR

TERMINALS

POWER

RESISTOR

POWER

BOARD

RIGHT SIDE OF MACHINE

INSULATED

GLOVES

INSULATED

PLIERS

FIGURE D.1

—

LOCATION OF INPUT FILTER CAPACITOR TERMINALS.

«
...
20
21
22
23
24
...
»

Содержание RED-D-ARC IM648-B






































Отзывы:

Нет отзывов

Похожие инструкции для RED-D-ARC IM648-B

Бренд: hager Страницы: 10

Бренд: 1byone Страницы: 17

Бренд: SMT Страницы: 24

Бренд: Uniden Страницы: 16

SpeedFace Series

Бренд: ZKTeco Страницы: 11

Бренд: DAB Страницы: 228

Бренд: Medion Страницы: 122

Бренд: INNO Instrument Страницы: 45

Бренд: Monitor Страницы: 14

Бренд: Kemppi Страницы: 31

JING BAO SS5500

Бренд: Qian Страницы: 70

Syn-Apps VIP-801A-SA

Бренд: Valcom Страницы: 2

Бренд: FY-TECH Страницы: 34

Headzone PRO XT

Бренд: Beyerdynamic Страницы: 28

POWERHORN SH10A

Бренд: X10 Страницы: 1

Бренд: Linde Страницы: 2

Бренд: HALDER Страницы: 2

Бренд: Forge Electronics Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды