manualshive.com logo in svg

Lincoln Electric RED-D-ARC IM648-B, Руководство оператора

Поделиться
Скачать
Lincoln Electric RED-D-ARC IM648-B Скачать руководство пользователя страница 21

C-1

ACCESSORIES

C-1

ALWAYS USE GENUINE LINCOLN
ELECTRIC ELECTRODES AND
VORTECH

™

 NOZZLES

•

  Only Genuine Lincoln Electric consumables yield

the best cutting performance for the PYTHON.

•

The patented VORTECH

™

nozzle provides an

extra

“

kick

”

 of swirl as the arc exits the nozzle which

improves cutting performance. No other nozzle has

this capability or can match its performance.

GENERAL OPTIONS / 
ACCESSORIES

The following options/accessories are available for
your PYTHON from your local Lincoln Distributor.

K1681-2 Undercarriage - A valet style undercarriage
with pull-out handle for machine only. Provides Torch
and Work Cable storage.

S22147-043 - VORTECH

™

nozzle with an .043

”

 (1.2

mm) Orifice (for 35 - 60 Amps)

S22147-053 - VORTECH

™

nozzle with an .053

”

 (1.3

mm) Orifice (for 60 - 85 Amps)

S22147-082 - VORTECH

™

nozzle with an .082

”

 (2.1

mm) Orifice (for Gouging at 60 - 85 Amps)

S22149 - Electrode - replacement electrodes for cut-
ting.

S22150 - Shield Cup - This shields the torch tip and
provides more visibility to the workpiece than the drag
cup. Note the shield cup does not prevent the torch tip
from touching the workpiece.

•

NOTE: the shield cup does not prevent the torch tip
from touching the workpiece.

S22151 - Drag Cup - The drag cup protects the torch
by preventing the torch from touching the workpiece.

K1571 Series - PCT 80 Torches come in 25

’

 and 50

’

lengths in either hand held or mechanized versions.

PYTHON

Содержание RED-D-ARC IM648-B






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды