Lincoln Electric PRISM DOWN DRAFT Скачать руководство пользователя страница 34

Страница: 34 / 44

E-3

TROUBLESHOOTING

Observe all Safety Guidelines detailed throughout this manual

PRISM

DOWN DRAFT WITH MECHANIZED CLEANING-MS/A ONLY

Fan does not start running.

Downdraft table does not func-

tion.

1. No compressed air available

or Low pressure - less than 60

psi (4 BAR)

1. Connect/repair compressed air

supply.

2. *Automatic start/stop (move-

ment sensor or welding cable

sensor) not connected.

2. *Connect cable of automatic

start / stop (*See Figure A.11,

item A).

3. *Movement sensor is defective. 3. *Replace sensor.
4. *Welding cable sensor not

connected.

4. *Connect clamp of welding

cable sensor to ground cable

of welding machine.

Irregular filter cleaning. One of the

filter cartridges is not being

cleaned.

1. One of the membrane valves

defective.

1. Replace both membrane

valves.

Poor extraction capacity. No filter

cleaning.

1. Membrane valve(s) defective.

1. Replace both membrane

valves.

2. Button RESET ALARM/MANU-

AL CLEANING defective.

2. Replace button RESET

ALARM/MANUAL CLEANING.

POSSIBLE

CAUSE

RECOMMENDED

COURSE OF ACTION

PROBLEMS

(SYMPTOMS)

The alarm lamp will be continu-

ously on
Filter cleaning system does not

function.

1. No compressed air available.

1 Connect/repair compressed air

supply.

* Accessory item.

OFFLINE MANUAL CLEANING

button does not work. No filter

cleaning.

1. Button was not pushed/held

long enough.

1. Push/hold button for 5 sec-

onds.

The alarm lamp will flash 2

Seconds on - 2 seconds off
Filter cartridges polluted.

1. Pressure over the filter car-

tridges has reached 0.22 psi

(1500 Pa.).

1. Switch off the fan to initiate the

automatic offline filter cleaning

cycle

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your

Lincoln Authorized Service Facility for technical troubleshooting assistance before you proceed.

WWW.LINCOLNELECTRIC.COM/LOCATOR

PRISM

DOWN DRAFT

& PRISM

DOWN DRAFT WITH MECHANIZED CLEANING

Содержание PRISM DOWN DRAFT













































Результаты поиска

Содержание PRISM DOWN DRAFT

Отзывы:

Похожие инструкции для PRISM DOWN DRAFT

Бренды по названию

Популярные бренды

Lincoln Electric PRISM DOWN DRAFT, Руководство оператора

Результаты поиска

Содержание PRISM DOWN DRAFT

Отзывы:

Похожие инструкции для PRISM DOWN DRAFT

Бренды по названию

Популярные бренды