Lincoln Electric DUAL VANTAGE 700 Скачать руководство пользователя

Страница: 33 / 96

D-1

MAINTENANCE

DUAL VANTAGE

700

SAFETY PRECAUTIONS

• Have qualified personnel do all maintenance

and troubleshooting work.

• Turn the engine off before working inside the

machine or servicing the engine.

• Remove guards only when necessary to

perform maintenance and replace them when

the maintenance requiring their removal is

complete. If guards are missing from the

machine, obtain replacements from a Lincoln

Distributor. (See Operating Manual Parts List.)

Read the Safety Precautions in the front of this

manual and in the Engine Owner’s Manual before

working on this machine.

Keep all equipment safety guards, covers, and

devices in position and in good repair. Keep

hands, hair, clothing, and tools away from the

gears, fans, and all other moving parts when

starting, operating, or repairing the equipment.

------------------------------------------------------------------------

ROUTINE AND PERIODIC MAINTENANCE

DAILY

• Check the Engine oil levels.

• Refill the fuel tank to minimize moisture condensa-

tion in the tank.

• Open the water drain valve located on the bottom of

the water separator element 1 or 2 turns and allow

to drain into a container suitable for diesel fuel for 2

to 3 seconds. Repeat the above drainage procedure

until diesel fuel is detected in the container.

• Check coolant level in the coolant recovery bottle.

------------------------------------------------------------------------

WEEKLY

Blow out the machine with low pressure air periodical-

ly. In particularly dirty locations, and the radiator, this

may be required once a week.

WARNING

ENGINE MAINTENANCE

Refer to the “Periodic Checks” section of the Engine

Operator’s Manual for the recommended maintenance

schedule of the following:

a) Engine Oil and Filter

b) Air Cleaner

c) Fuel Filter - and Delivery System

d) Alternator Belt

e) Battery

f ) Cooling System

Refer to Table D.1 at the end of this section for vari-

ous engine maintenance components.

AIR FILTER

• Excessive air filter restriction will result in

reduced engine life.

• Never use gasoline or low flash point solvents

for cleaning the air cleaner element. A fire or

explosion could result.

• Never run the engine without the air cleaner.

Rapid engine wear will result from contaminants,

such as dust and dirt being drawn into the

engine.

------------------------------------------------------------------------

The diesel engine is equipped with a dry type air filter.

Never apply oil to it. Service the air cleaner as follows:

Replace the element as indicated by the service indi-

cator. (See Service Instructions and Installation Tips

for Engine Air Filter.)

CAUTION

WARNING

MAINTENANCE

Содержание DUAL VANTAGE 700

































































































Результаты поиска

Содержание DUAL VANTAGE 700

Отзывы:

Похожие инструкции для DUAL VANTAGE 700

Бренды по названию

Популярные бренды

Lincoln Electric DUAL VANTAGE 700, Руководство оператора

Результаты поиска

Содержание DUAL VANTAGE 700

Отзывы:

Похожие инструкции для DUAL VANTAGE 700

Бренды по названию

Популярные бренды