Lincoln Electric DUAL VANTAGE 700 Скачать руководство пользователя

Страница: 13 / 96

A-4

INSTALLATION

DUAL VANTAGE

700

ENGINE COOLANT

HOT COOLANT can burn skin.
•Do not remove cap if radiator is hot.

------------------------------------------------------------------------

The welder is shipped with the engine and radiator

filled with a 50% mixture of ethylene glycol and water.

See the MAINTENANCE section and the engine

Operator’s Manual for more information on coolant.

BATTERY CONNECTION

GASES FROM BATTERY can explode.
• Keep sparks, flame and cigarettes

away from battery.

To prevent EXPLOSION when:

• INSTALLING A NEW BATTERY — disconnect

negative cable from old battery first and connect

to new battery last.

• CONNECTING A BATTERY CHARGER — remove

battery from welder by disconnecting negative

cable first, then positive cable and battery clamp.

When reinstalling, connect negative cable last.

Keep well ventilated.

• USING A BOOSTER — connect positive lead to

battery first then connect negative lead to nega-

tive battery lead at engine foot.

BATTERY ACID can burn eyes and skin.
• Wear gloves and eye protection and

be careful when working near battery.

• Follow instructions printed on battery.

------------------------------------------------------------------------

IMPORTANT

: To prevent ELECTRICAL DAMAGE

WHEN:

a) Installing new batteries.
b) Using a booster.

Use correct polarity —

Negative Ground.

PRE-OPERATION ENGINE SERVICE

READ the engine operating and maintenance instruc-

tions supplied with this machine.

• Keep hands away from the engine

muffler or HOT engine parts.

• Stop engine and allow to cool before

fuelling.

• Do not smoke when fuelling.
• Fill fuel tank at a moderate rate and do not over-

fill.

• Wipe up spilled fuel and allow fumes to clear

before starting engine.

• Keep sparks and flame away from tank.

------------------------------------------------------------------------

OIL

The DUAL VANTAGE

700 is shipped with the engine

crankcase filled with high quality SAE 10W-30 oil (API

class CD or better). Check the engine oil levels before

starting the engine. If it is not up to the full mark on the

dip stick, add oil as required. Check the oil level every

four hours of running time during the first 35 running

hours. Refer to the engine Operator’s Manuals for

specific oil recommendations and break-in informa-

tion. The oil change interval is dependent on the quali-

ty of the oil and the operating environment. Refer to

the engine Operator’s Manuals for the proper service

and maintenance intervals.

FUEL
USE DIESEL FUEL ONLY

•

Fill the fuel tank with clean, fresh diesel fuel. The

capacity of the fuel tank is approximately 25 gallons

(95 liters). See engine Operator’s Manual for specif-

ic fuel recommendations.

Running out of fuel may

require bleeding the fuel injection pump.

NOTE:

Before starting the engine, open the fuel shut-

off valve (pointer to be in line with hose).

FUEL CAP

Remove the plastic cap covering from the Fuel Tank

Filler neck and install the Fuel Cap.

WARNING

Содержание DUAL VANTAGE 700

































































































Результаты поиска

Содержание DUAL VANTAGE 700

Отзывы:

Похожие инструкции для DUAL VANTAGE 700

Бренды по названию

Популярные бренды

Lincoln Electric DUAL VANTAGE 700, Руководство оператора

Результаты поиска

Содержание DUAL VANTAGE 700

Отзывы:

Похожие инструкции для DUAL VANTAGE 700

Бренды по названию

Популярные бренды