Lightmed TruScan 532 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 115

background image

TruScan 532 Single - Wavelength – Operators Manual Rev. No 02

Page 39 of 114

between each pulse of the treatment laser. Similar to the Duration switches, the

left hand control will decrease the interval and the right hand control will increase

the interval. In this mode the repeat pulse rate cannot be set higher   than  a  50%  duty
cycle.  This means that the laser fire duration cannot be higher  than  the  repeat  interval
duration.  It means also that the repeat interval duration   is greater than or equal to the
exposure duration when pressing the down   setting  switch.    The  minimum  interval  is
0.01 seconds, and the maximum interval   is  3.0  seconds.    If  the  interval  is  adjusted
beyond 3.0 seconds, then the Repeat  Interval  display  will  show  “One”  where  the
footswitch must be pressed every

time the doctor/user wishes to fire the laser.

9. Aiming Beam Intensity Indicator display

This display gives an indication of the brightness of the Aiming beam intensity. When
more of the bar graphs are displayed, then the brightness is higher. At the maximum
brightness the output power will be around 1.0mw or less to the patient’s cornea.

10. Aiming Beam Intensity button

The brightness of the Aiming beam is adjusted with these 2 switches.

11. LIO Illumination Intensity Bar Indicator

This bar graph is the intensity indicator.

12. LIO Illumination Setting button

When the LIO is connected to the TruScan 532 Single-Wavelength Laser Console,
this control can be used to adjust the intensity of the Illumination lamp.

13

.

Warning Volume Control Button / Display Bar

This control can be used to adjust the volume of the laser fire audible warning.
However the audible warning cannot be turned off.

14. Total Laser Counts display

This display gives a sum of the total number of Laser shots fired during the laser
treatment.

15. Counter Reset Button

Whenever this switch is pressed the total laser shot counter is reset to zero.

16. Type of Delivery System Indicator

This indicator will indicate the type is being used.

«
...
38
39
40
41
42
...
»

Содержание TruScan 532




















































































































Отзывы:

Нет отзывов

Похожие инструкции для TruScan 532

Бренд: Kawai Страницы: 33

Бренд: Kawai Страницы: 60

Бренд: ICT Страницы: 48

Бренд: OfiTE Страницы: 67

Бренд: Bacharach Страницы: 28

Бренд: Narvitech Страницы: 2

Electone Stagea ELS-01C

Бренд: Yamaha Страницы: 248

Бренд: Trebs Страницы: 44

Greenlee CLM-1000

Бренд: Textron Страницы: 36

SPEEDLOADER BRIDGE SYSTEM

Бренд: Floyd Rose Страницы: 10

Бренд: Badger Meter Страницы: 24

Бренд: Rae Страницы: 38

Бренд: FlowLine Страницы: 2

Бренд: SANKO Страницы: 97

Бренд: Staco Energy Страницы: 2

Бренд: TA Instruments Страницы: 68

Бренд: Omega Страницы: 4

LiveTester LT 220

Бренд: StarLogixs Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды