Lightmed TruScan 532 Скачать руководство пользователя страница 107

Страница: 107 / 115

TruScan 532 Single - Wavelength – Operators Manual Rev. No 02

Page 106 of 114

8.2 Warning

A completed listing of Lightlas system warming and the suggested corrective action are
detailed as following:

A complete listing of the TruScan 532 Single-Wavelength system warning along with the
suggested corrective actions are shown below:

Error code

Cause(s) / Description

Remedy Action(s)

Safety filter not
found

-Safety filter not connect
to the console or loosen
with console

-Please connect the safety filter to the
console.

Red diode
temperature not
ready

-Diode is not according to
ambient temperature

-Please wait while the console adjusts
itself according to ambient
temperature

-This process may take up to five
minutes to complete.

LBO temperature
not ready

-LBO is not according to
ambient temperature

-Please wait while the console adjusts
itself according to ambient
temperature

-This process may take up to five

System
Warning
Message

Corrected
Actions

Содержание TruScan 532




















































































































Результаты поиска

Содержание TruScan 532

Отзывы:

Похожие инструкции для TruScan 532

Бренды по названию

Популярные бренды

Lightmed TruScan 532, Руководство оператора

Результаты поиска

Содержание TruScan 532

Отзывы:

Похожие инструкции для TruScan 532

Бренды по названию

Популярные бренды