background image

Lighthouse REMOTE Liquid Particle Counter (MODBUS Output) Operating Manual

3-4

248083227-1 Rev 8

Communication Ports

WARNING: 

When 

daisy chaining multiple 
instruments, connect IN 
ports only to OUT ports.  
DO NOT connect an IN 
port to another IN port.  
Doing so will damage the 
sensor and void the 
warranty.

The RS232/485 IN port incorporates Serial and MODBUS 
communications to allow short distance point-to-point RS232 or long 
distance multi-point RS485 communications.

The RS232 protocol is provided for quick simple cable connections to a 
standard PC COM port and is used for single-unit communications 
only.

The RS485 protocol is provided for industrial applications with 
multiple devices on the same bus and requires an adapter when used 
with a PC.  The RS485 IN and OUT connectors allow easy connections 
using standard CAT 5 patch cables commonly used for office LANs.  
Connecting the counter to a PC via RS485 requires an RS485 to RS232 
converter, cables, connectors and terminator;  please contact a 
Lighthouse Sales Representative for the LWS RS485 converter kit.

For more information, please see chapter on “Communications” on 
page 4-1.

RS485 Adapter Cable

WARNING: 

Failure to 

use the Adapter Cable in 
a daisy-chain network 
may damage the RLPC 
and void its warranty.

An RS485 Adapter Cable is available as an optional accessory and 
must be used to connect the RLPC to an RS485 daisy-chain network.  
The adapter prevents damage to the instrument when it is used in daisy-
chain networks.  Plug it into the RS232/485 IN port before connecting 
the network cable to the RLPC. See Figure 3-4.

Figure 3-4  RS485 Adapter Cable

Note: 

Use of the Adapter 

Cable for RS232 or RS485 
Hub connections may not 
provide the desired results.

If the RLPC will be used in a point-to-point RS232 connection, the 
Adapter Cable should not be used.  RS232 communication to the RLPC 
will be blocked if the adapter is in place.

If the RLPC will be used in a star configuration using an RS485 hub, 
the Adapter Cable should not be used if the hub is supplying power to 
the instrument.  Power to the RS232/485 IN port will be blocked if the 
adapter is in place.

Содержание RLPC 0.1m























































































































Отзывы: