Lifebreath 1200 POOL Скачать руководство пользователя страница 24

Страница: 24 / 32

Reverse Installation of the HRV

Damper Removal:

Reinstalling the Damper Motor:

Electrical Box Removal:

Remove the door panels from the HRV by

loosening the screws located on the face of the

doors.

Remove the electrical box cover by removing

the 4 screws fastening the cover in place.

3. Disconnect the motor wires coming through the

bottom of the electrical box from the circuit
board, capacitors and relays, and remove from
the electrical box.

4. Pull motor wires for lower blower through hole

in blower divider panel.

5. Disconnect damper motor wires (three) from the

circuit board and remove from the electrical box.

Disconnect thermistor from circuit board and

remove from electrical box.

7. Remove the 4 screws securing the electrical box

to the cabinet of the HRV.

8. Remove the ground continuity screw from both the

upper and lower blower pans securing them to
the pan stops.

14. On the opposite side of the HRV, place the

damper motor over the square damper rod

aligning the end of the rod flush with the

damper motor.

15. Install the machine screw and kep nut which

fastens the damper motor to the bracket.

16. Insert the shim around the damper rod ensuring

it is placed on the opposite side of the rod from

the set screws. Both of the set screws should

screw directly into the damper rod, not the shim.

17. Prior to tightening the set screws ensure proper

alignment of the damper door such that it is

evenly spaced over the port collars providing a

good seal in both directions.

18. Once alignment is confirmed, tighten the set

screws to secure the damper into place.

19. Remove the snap plug from the hole in the top

core support panel, and install a plastic snap

bushing in hole.

20. Route damper motor wires through hole in top

core support panel.

9. Cut cable tie fastening thermistor wire to

bracket, disconnect thermistor from circuit,

and remove thermistor.

10. On the damper motor, loosen the two set

screws which hold the square damper rod in

place using a 1/8” hex key.

11. Remove the machine screw and kep nut fastening

the damper motor to the bracket.

12. Remove the damper motor from the bracket and

ensure that the two shims are collected from either
side of the damper rod, and by pulling the damper
motor wires out from the top core support panel.

13. Remove the plastic snap bushing from the hole in

the top core support panel where the damper wires
were removed from, and install a snap plug to seal
the hole, found in the manual bag.

Содержание 1200 POOL

































Результаты поиска

Содержание 1200 POOL

Отзывы:

Похожие инструкции для 1200 POOL

Бренды по названию

Популярные бренды

Lifebreath 1200 POOL, Руководство по эксплуатации и установке

Результаты поиска

Содержание 1200 POOL

Отзывы:

Похожие инструкции для 1200 POOL

Бренды по названию

Популярные бренды