background image

3.

Grasp the other rear cover and slowly lift the rear foot off the floor. Lower rear foot to the floor.
Make note of either rear foot lifting off the floor easier than the other.
If both rear feet lift off the floor evenly, secure both leveling foot jam nuts against the frame post using a 9/16”
open-end wrench. Unit is leveled.
Left leveling foot shown

Item

Description

Qty.

1

Frame Post

1

2

Jam Nut

1

3

Leveling Foot

1

4

Turn Counter-Clockwise to Secure

4.

Adjust the weight of the rear feet using a 1/2” open-end wrench.

• If the 

left

 rear foot lifts up easier, Adjust the 

right

 leveling foot nut down.

• If the 

right

 rear foot lifts up easier, Adjust the 

left

 leveling foot nut down.

Left leveling foot shown

Item

Description

Qty.

1

Frame Post

1

2

Leveling Foot Nut

1

3

Leveling Foot

1

4

Turn Clockwise to Adjust Leveling Foot

Down

5.

Test the unit again for uneven weight on the rear feet. Adjust leveling foot nuts until each rear foot lifts with even
force.

6.

Secure both jam nuts using a 9/16” open-end wrench. Unit is leveled.

Page 40 of 47

Содержание INA-CS



















































Отзывы: