Liebert ITA UPS 16kVA Скачать руководство пользователя страница 16

Страница: 16 / 48

8 Chapter 2 Installation

Liebert ITA 16kVA/20kVA User Manual

2.4 Mechanical Installation

Note

The UPS is suitable for resistive-capacitive load (like computer), resistive load and micro-inductive load. It is not suitable for purely

inductive load or purely capacitive load (like motor, air-conditioner and duplicator), nor can it be connected to half-wave rectifier

load.

Two installation modes are available: tower installation and rack installation. You can select an appropriate installation

mode according to the actual conditions.

According to the different configuration requirements, the UPS has two configurations: battery modules excluded, and

four battery modules. For tower installation, you should prepare the battery rack and battery cabinet for installing the

battery modules; for rack installation, the battery modules and the UPS can be installed in the same rack together.

2.4.1 Tower Installation

1. Assemble a pair of support bases (accessories) and a support base extension (accessory) together through

fastenings, as shown in Figure 2-1.

Support base

Fastening

Support base extension

Figure 2-1 Connecting the support base with support base extension

2. Repeat step 1 to connect another pair of support bases with a support base extension.

3. Place the UPS on the support bases and support base extensions, as shown in Figure 2-2.

Support base

UPS

Support base

Figure 2-2 Installation complete

Note

For tower installation, two pairs of support bases should be placed respectively at both sides of the UPS, as shown in Figure 2-2.

Otherwise, the UPS may be dumped.

Содержание ITA UPS 16kVA

















































Результаты поиска

Содержание ITA UPS 16kVA

Отзывы:

Похожие инструкции для ITA UPS 16kVA

Бренды по названию

Популярные бренды

Liebert ITA UPS 16kVA, Руководство пользователя

Результаты поиска

Содержание ITA UPS 16kVA

Отзывы:

Похожие инструкции для ITA UPS 16kVA

Бренды по названию

Популярные бренды