background image

11

Multi-Protocol Operation 

Analog Operation

This decoder can also be operated on analog layouts or areas of track that are 

analog. The decoder recognizes alternating current (DC) and automatically adapts 

to the analog track voltage. All functions that were set under mfx or DCC for analog 

operation are active (see Digital Operation).

Digital Operation

The decoders are multi-protocol decoders. These decoders can be used under the 

following digital protocols: mfx or DCC.

The digital protocol with the most possibilities is the highest order digital protocol. 

The sequence of digital protocols in descending order is:

Priority 1: mfx; Priority 2: DCC; Priority 3: DC

Note:

 Digital protocols can influence each other. For trouble-free operation, we re-

commend deactivating those digital protocols not needed by using CV 50. Deactivate 

unneeded digital protocols at this CV if your controller supports this function. 

If two or more digital protocols are recognized in the track, the decoder automatically 

takes on the highest order digital protocol, example: mfx/DCC; the decoder takes on 

the mfx digital protocol (see previous table).

Note: 

Please note that not all functions are possible in all digital protocols. Several 

settings for functions, which are supposed to be active in analog operation, can be 

done under mfx and DCC. 

Notes on digital operation 

•   The operating instructions for your central unit will give you exact procedures for 

setting the different parameters. 

•   The values set at the factory have been selected for mfx in order to guarantee the 

best possible running characteristics.  

Adjustments may have to be made for other operating systems. 

•  The setting done at the factory does not permit operation with opposite polarity 

DC power in the braking block. If you want this characteristic, you must do without 

conventional DC power operation (CV 29/Bit 2 = 0). 

mfx Protocol

Addresses 

•   No address is required; each decoder is given a one-time, unique identifier (UID).

•   The decoder automatically registers itself on a Central Station or a Mobile Station 

with its UID-identifier.

Programming 

•   The characteristics can be programmed using the graphic screen on the Central 

Station or also partially with the Mobile Station.

•   All of the Configuration Variables (CV) can be read and programmed repeatedly.

•   The programming can be done either on the main track or the programming track.

•   The default settings (factory settings) can be produced repeatedly.

•   Function mapping: Functions can be assigned to any of the function but-

tons with the help of the 60212 Central Station (with limitations) and with the 

60213/60214/60215 Central Station (See help section in the Central Station).

DCC Protocol

Addresses 

•   Short address – long address – multiple unit address

•   Address range:  

1 – 127 for short address and multiple unit address,  

1 – 10239 for long address 

•   Every address can be programmed manually.

•   Short or long address is selected by means of CV 29 (Bit 5).

•   A multiple unit address that is being used deactivates the standard address. 

Programming

•   The characteristics can be changed repeatedly using the Configuration Variables 

(CV).

•   The CV numbers and the CV values are entered directly.

•   The CVs can be read and programmed repeatedly. (Programming is done on the 

programming track.)

•   The CVs can be programmed in any order desired. (PoM - Programming can be 

done on the main track). PoM is not possible with CVs CV 1, 17, 18,and 29. PoM 

must be supported by your central controller (Please see the description for this 

unit.).

•   The default settings (factory settings) can be produced repeatedly.

•   14/28 or 126 speed levels can be set.

•   All of the functions can be controlled according to the function mapping (see CV 

description).

•   See the CV description for the DCC protocol for additional information.

We recommend that in general programming should be done on the programming 

track.

Содержание 25558

















































Отзывы: