LG V24LH Скачать руководство пользователя страница 7

Страница: 7 / 31

ENGLISH

Installation Manual

Installation of Indoor, Outdoor Unit

1076

Suspension

bolt

Center-line for the

piping hole

(Unit : mm)

265

1236

265

Install Plate

5~7mm

Indoor

Outdoor

WALL

Side Plate

Inlet Grille

Inlet hanger

Hanger

screw

1. Indoor unit installation

■

Before Installing, prepare Installation
Plates

• 'Installation Plates' are attached at the bottom of

indoor unit.
Detach them by removing each 3 screws at both
sides.

• Pull the upper right and left side of 'Inlet Grille' to

the front, and it will stop at slightly tilted position.

• Unhook the 'Inlet hanger' from the 'Hanger screw'

on the both left and right side.

• Detach the 'Inlet Grille' from the Indoor Unit.
• Detach 'Side Plate (R,L)' by removing each 3

screws on both sides.

1) Installation on the ceiling

• Measure and mark the position for the Suspension

bolts and the piping hole.

• Drill the hole for anchor nut on the ceiling.

Before secure the Installation Plates, select
the bent direction of the Installion Plate to the
inside or the outside according to the
installation circumstances.

• Drill the piping hole on the wall slightly tilted to the

outdoor side using a ø70 hole-core drill.

■

VB CHASSIS

Содержание V24LH
































Результаты поиска

Содержание V24LH

Отзывы:

Похожие инструкции для V24LH

Бренды по названию

Популярные бренды

LG V24LH, Руководство по установке

Результаты поиска

Содержание V24LH

Отзывы:

Похожие инструкции для V24LH

Бренды по названию

Популярные бренды