LG V24LH Скачать руководство пользователя страница 24

Страница: 24 / 31

Convertible Air Conditioner

Connecting Cables between Indoor Unit and Outdoor Unit

Connecting Cables between Indoor Unit and Outdoor Unit

AIR GUIDE-L

INDOOR UNIT

Control

Panel

Clamp

• Cooling Model Only

1(L) 2(N) 1(L) 2(N) 3

Terminals on the indoor unit

Power Input

Terminals on the outdoor unit

1(L) 2(N)

• Heat Pump Model Only

1(L) 2(N) 1(L) 2(N) 3

Terminals on the indoor unit

Power Input

Terminals on the outdoor unit

1(L) 2(N)

The power cord

connected to the indoor

unit should be complied with the following
specifications (Type H05VV-F(Indoor)
approved by HAR or SAA).

The power connecting cable

connected between the indoor
and outdoor unit should be
complied with the following
specifications
(Type H07RN-F approved by
HAR or SAA).

•

20mm

GN/YL

20mm

GN/YL

NORMAL
CROSS-SECTIONAL
AREA 0.75mm

(18k/24k/28k)

Cooling Only

Heat Pump

4 x 0.75

(Including Earth)

5 x 0.75

(Including Earth)

CAUTION

1) Connecting cables to the Indoor Unit

1) Remove the Air guide - L by loosening 2 screws

after removing the Inlet grille from the Indoor unit.

2) Connect the wires to the terminals on the control

board individually according to the outdoor unit
connection.

• Ensure that the color of the wires of outdoor unit and

the terminal No. are the same as those of indoor unit
respectively

2) Clamping of cables

1) Arrange the connecting cable on the control panel.
2) First, fasten the steel clamp with a screw to the inner boss of control panel.
3) For the cooling model, fix the other side of the clamp with a screw strongly.

For the heat pump model, put the 0.75mm

cable(thinner cable) on the clamp and tighten it with a plastic

clamp to the other boss of the control panel.

4) In Australia, the length of power supply cord measured from the entry of the power supply cord to the middle

of live pin on the power plug should be over 1.8m.

Содержание V24LH
































Результаты поиска

Содержание V24LH

Отзывы:

Похожие инструкции для V24LH

Бренды по названию

Популярные бренды

LG V24LH, Руководство по установке

Результаты поиска

Содержание V24LH

Отзывы:

Похожие инструкции для V24LH

Бренды по названию

Популярные бренды