LG V24LH Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 31

background image

12

Convertible Air Conditioner

Installation of Indoor, Outdoor Unit

• Before working, refer to "Connecting the
pipes to the Indoor Unit" on page 16.

R

Inner slot

Install the Indoor unit onto Installation Plate.
• Insert 2 hooks on the both left and right side of the

unit to the inner slot (wall side) of the Installation
Plate.

• Secure the unit to the Installation Plate with four M8

bolts and washers.

• Fit the projection hooks of the side plates to the

'Side Panel' and the 'Front Panel' by
lifting it.

• Fasten the screws.

• Hook up the Inlet Grille Hook to the cabinet.
• Hang the Inlet Hanger to the screw.

«
...
10
11
12
13
14
...
»

Содержание V24LH
































Отзывы:

Нет отзывов

Похожие инструкции для V24LH

Бренд: Olimpia splendid Страницы: 124

Бренд: d2itsu Страницы: 20

Voyager RT-SVX17C-EN

Бренд: Trane Страницы: 80

M thermal Mono Series

Бренд: Midea Страницы: 80

smart Ultra-Air Mist AP9S

Бренд: Momax Страницы: 35

GJC12AG-E6DRNB9A

Бренд: Gree Страницы: 50

Бренд: Baileigh Industrial Страницы: 32

Бренд: Daikin Страницы: 44

OTEC IEFC-D Series

Бренд: Omega Страницы: 12

Бренд: Seifert Страницы: 20

Бренд: York Страницы: 44

Бренд: Vaco Страницы: 113

Бренд: York Страницы: 56

ADAPT Parasol b 1200

Бренд: Swegon Страницы: 37

Бренд: Perfect Aire Страницы: 20

Бренд: Midea Страницы: 142

Бренд: Airrex Страницы: 16

Бренд: Gree Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды