LG V-NET PQCPC22A0 Скачать руководство пользователя

Страница: 3 / 125

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

Always comply with the following precautions to avoid dangerous situations and ensure peak
performance of your product

WARNING

It can result in serious injury or death when the directions are ignored

CAUTION

It can result in minor injury or product damage when the directions are ignored

WARNING

• Installation or repairs made by unqualified persons can result in hazards to you and others.

• Installation MUST conform with local building codes or, in the absence of local codes, with

the Nation Electrical Code NFPA 70/ANSI C1-1003 or current edition and Canadian Electrical
Code Part1 CSA C.22.1.

• The information contained in the manual is intended for use by a qualified service technician

familiar with safety procedures and equipped with the proper tools and test instruments.

• Failure to carefully read and follow all instructions in this manual can result in equipment mal-

function, property damage, personal injury and/or death.

Installation

• Any question about the product installation should be asked to the service center or the professional

installation agency.
- It may cause fire, electric shock, explosion or injury.

• Consult the service center or the professional installation agency about reinstalling the installed product.

- It may cause fire, electric shock, explosion or injury.

• Please use the standardized parts.

- It may cause fire, electric shock, explosion, injury, or failure.

• Do not keep or use combustible gas or inflammable material near the product.

- IT may cause fire or electric shock.

• Do not disassemble, repair or modify the product at random.

- It may cause failure of the product.

• Do not install where raindrop can fall.

- It may cause failure of the product.

• Do not install the product at wet place.

- It may cause failure of the product.

• Provided product and adaptor shall only be installed and used inside a building.

- It may cause fire or failure of the product.

*Do not install or use outside.

• Install stably in a place that can endure the weight of the ACP.

- If the installation place is not strong enough, the ACP may fall and damaged.

• Make sure to enquire to the specialty store of the product purchase or service center for electric works.

- It may cause fire or electric shock.

• Do not damage the power cord or bend it by force.

- It may cause fire or electric shock.

• You need to use a safely insulated power supply which follows IEC61558-2-6 and NEC Class2

- If you do not follow, It may cause fire, electric shock, explosion or injury.

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

Содержание V-NET PQCPC22A0






























































































































Результаты поиска

Содержание V-NET PQCPC22A0

Отзывы:

Похожие инструкции для V-NET PQCPC22A0

Бренды по названию

Популярные бренды

LG V-NET PQCPC22A0, Инструкция по установке и эксплуатации

Результаты поиска

Содержание V-NET PQCPC22A0

Отзывы:

Похожие инструкции для V-NET PQCPC22A0

Бренды по названию

Популярные бренды