LG multi V ARUV100DTS4 Скачать руководство пользователя

Страница: 22 / 33

ENGLISH

Precautions when laying power wiring

Use round pressure terminals for connections to the power terminal
block.

Round pressure terminal

Power cable

When none are available, follow the instructions below.
- Do not connect wiring of different thicknesses to the power terminal

block. (Slack in the power wiring may cause abnormal heat.)

- When connecting cable which is the same thickness, do as shown in

the figure below.

- For wiring, use the designated power cable and connect firmly, then

secure to prevent outside pressure being exerted on the terminal
block.

- Use an appropriate screwdriver for tightening the terinal screws. A

screwdriver with a small head will strip the head and make proper
tighterning impossible.

- Over-tightening the terminal screws may break them.

CAUTION

• Use the 2-core shield cables for communication cables. Never use

them together with power cables.

• The conductive shielding layer of cable should be grounded to the

metal part of both units.

• Never use multi-core cable
• As this unit is equipped with an inverter, to install a phase leading

capacitor not only will deteriorate power factor improvement effect,
but also may cause capacitor abnormal heating. Therefore, never in-
stall a phase leading capacitor.

• Make sure that the power unbalance ratio is not greater than 2%. If

it is greater the units lifespan will be reduced.

Control box and connecting position of wiring

- Remove all of the screws at front panel and remove the panel by

pulling it forward.

- Connect communication cable between main and sub outdoor unit

through the terminal block.

- Connect communication cables between outdoor unit and indoor

units through the terminal block.

- When the central control system is connected to the outdoor unit, a

dedicated PCB must be connected between them.

- When connecting communication cable between outdoor unit and in-

door units with shielded cable, connect the shield ground to the earth
screw.

Front Panel

2-Core Shield Cable

Multi-Core Cable

Remote

control

Remote

control

Remote

control

Remote

control

Indoor

Unit

Outdoor Unit

Indoor

Unit

Indoor

Unit

Indoor

Unit

Outdoor Unit

Remote

control

Remote

control

Indoor

Unit

Indoor

Unit

Remote

control

Remote

control

Indoor

Unit

Indoor

Unit

Master

Slave1

Slave2

Remote

controller

Remote

controller

Indoor

Unit

Indoor

Unit

Remote

controller

Outdoor Unit

Remote

controller

Indoor

Unit

Indoor

Unit

Master

Slave1

Slave2

Master

Slave1

Slave2

Outdoor Unit

Remote

controller

Remote

controller

Indoor

Unit

Indoor

Unit

Remote

controller

Remote

controller

Indoor

Unit

Indoor

Unit

Master

Slave1

Slave2

Outdoor Unit

2-Core Shield Cable

Multi-Core Cable

Содержание multi V ARUV100DTS4


































Результаты поиска

Содержание multi V ARUV100DTS4

Отзывы:

Похожие инструкции для multi V ARUV100DTS4

Бренды по названию

Популярные бренды

LG multi V ARUV100DTS4, Руководство по установке

Результаты поиска

Содержание multi V ARUV100DTS4

Отзывы:

Похожие инструкции для multi V ARUV100DTS4

Бренды по названию

Популярные бренды