LG MS-2642FB Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 35

background image

5-15

CONDITION

CHECK

RESULT

CAUSE

REMEDY

No microwave
oscillation.

No continuity.

Continuity.

Abnormal

Defective high
voltage
transformer.

Replace high
voltage
transformer.

Normal

Defective PCB
assembly.

Replace PCB
assembly.

Disconnect the
wire leads from
relay 2 and
check continuity
of relay 2.
(Operate the unit)

Check high vol-
tage transformer

Output is full power
when you set lower
power level.

Abnormal.

Defective PCB
assembly.

Replace PCB
assembly.

Disconnect the
wire leads from
relay 2 and check
continuity relay 2.
(Operate the unit)

Abnormal

Defective high
voltage capacitor.

Replace high
voltage capacitor.

Normal

Check high vol-
tage capacitor.

Abnormal

Defective high
voltage diode.

Replace high
voltage diode.

Normal

Check high vol-
tage diode.

Abnormal

Defective
magnetron.

Replace
magnetron.

Check
magnetron.

(TROUBLE 5) No microwave oscillation even though oven lamp and fan motor run.

(Display operates properly)

NOTE : • Make sure the wire leads are in the correct position.

• When removing the wire leads from the parts, be sure to grasp the connector, not the wires.
• When removing the magnetron, be sure to install the magnetron gasket in the correct position

and in good condition.

«
...
23
24
25
26
27
...
»

Содержание MS-2642FB




































Отзывы:

Нет отзывов

Похожие инструкции для MS-2642FB

Renaissance RO130

Бренд: Dacor Страницы: 20

Бренд: Daewoo Страницы: 31

Бренд: Bauknecht Страницы: 98

Бренд: Raytheon Страницы: 60

Бренд: GE Страницы: 68

Бренд: Blaupunkt Страницы: 72

Бренд: Fama Страницы: 24

Бренд: Brandt Страницы: 104

B45M42 3 Series

Бренд: NEFF Страницы: 28

Бренд: Brandt Страницы: 27

Бренд: Samsung Страницы: 180

Бренд: Fagor Страницы: 66

Бренд: Jocel Страницы: 62

Бренд: Brandy Best Страницы: 54

Бренд: Frigidaire Страницы: 4

Бренд: Frigidaire Страницы: 10

Бренд: Frigidaire Страницы: 1

Бренд: Frigidaire Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды