LG MS-2642FB Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 35

background image

1. Incomplete segments.

• Segment missing.
• Partial segment missing.
• Digit flickering (NOTE: Slight flickering is normal.)

2. Colon does not turn on or blink.
3. A distinct change in the brightness of one or more numbers in display.
4. One or more digits in the display are not lighting.
5. Display indicates a number different from one touched, for example, key in 5 and 3 appears in the display.
6. Specific numbers (for example 7 or 9) will not display when key pad is touched.
7. Display does not count down with time blinking or up with clock operation.
8. Display obviously jumps in time while counting down.
9. Display counts down too fast while cooking.

10. Each indicator light does not turn on after setting cooking cycle.
11. Display time of day does not reappear when cooking is finished.

5-12

(TROUBLE 1) The following visual conditions indicate a probable defective control circuit.

CONDITION

CHECK

RESULT

CAUSE

REMEDY

1. No input can be

programmed.

Continuity

No continuity

Defective PCB
assembly.

Loose
connection.

Replace PCB
assembly.

Connect them
tightly.

Check the conn-
ection between
membrane key
assembly and
PCB assembly.

2. Some inputs

cannot be
programmed.

3. Display shows a

number or figure
different from one
touched.

4. Random

programming
when touching
other pads.

5. Display is fixed

at some figure
and can not
accept any
input.

Everything works
as specified.

Still have trouble.

Defective key
membrane
assembly.

Defective PCB
assembly.

Replace key
membrane
assembly.

Replace PCB
assembly.

Replace key
membrane
assembly and
check operation.

«
...
20
21
22
23
24
...
»

Содержание MS-2642FB




































Отзывы:

Нет отзывов

Похожие инструкции для MS-2642FB

Monogram ZMC1095 Series

Бренд: GE Страницы: 36

Convection Grill Combination Microwave

Бренд: GE Страницы: 6

Monogram ZMC1095 Series

Бренд: GE Страницы: 8

Бренд: GE Страницы: 24

Бренд: GE Страницы: 20

Advantium CSB9120

Бренд: GE Страницы: 32

Бренд: Samsung Страницы: 120

Бренд: Samsung Страницы: 28

Бренд: Samsung Страницы: 25

Бренд: Samsung Страницы: 24

Бренд: Samsung Страницы: 3

Бренд: Samsung Страницы: 32

Бренд: Daewoo Страницы: 25

Бренд: Daewoo Страницы: 32

Бренд: Daewoo Страницы: 23

Бренд: Daewoo Страницы: 18

Бренд: Daewoo Страницы: 8

Бренд: DAEWOO ELECTRONICS Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды