LG MS-2642FB Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 35

background image

D. PCB ASSEMBLY REMOVAL

1) Remove the control panel assembly from the

cavity. (Refer to control panel assembly removal
on previous page.)

2) Remove screws which hold the PCB SUB

ASSEMBLY to the control panel.

3) Disconnect the flat cable from the PCB SUB

ASSEMBLY and take off the PCB SUB ASSEMBLY.

E. DOOR MAIN ASSEMBLY REMOVAL

1) Open the door.
2) Remove the choke cover very carefully with a flat-blade

screwdriver.

CAUTION: Be careful not to damage door seal plate

by screwdriver.

3) Lift up and push the door.

NOTE:
1. After replacing the door, be sure to check that the

primary switch, monitor switch, and secondary switch
operate normally.

2. After replacing the door, check for microwave energy

leakage with a survey meter. Microwave energy must
be below the limit of 4 mW/cm. (with a 275 ml water
load)

3. When mounting the door assembly to the oven

assembly, be sure to adjust the door assembly parallel
to the chassis. Also, adjust so the door has no play
between the inner door surface and oven frame
assembly. If the door assembly is not mounted
properly, microwaves may leak from the clearance
between the door and the oven.

5-4

Door seal plate

Key Membrane

Control Panel

PCB Sub Asm

Remove door

Remove choke cover

Spacer

«
...
12
13
14
15
16
...
»

Содержание MS-2642FB




































Отзывы:

Нет отзывов

Похожие инструкции для MS-2642FB

Бренд: Panasonic Страницы: 23

Inverter NN-CF770M

Бренд: Panasonic Страницы: 38

Inverter NN-L564

Бренд: Panasonic Страницы: 46

Genius NN-SN667B

Бренд: Panasonic Страницы: 30

Genius NN-SD767S

Бренд: Panasonic Страницы: 8

Genius NN-SD697S

Бренд: Panasonic Страницы: 30

inverter NN-GD569M

Бренд: Panasonic Страницы: 22

In-A-Drawer MMDV30

Бренд: Dacor Страницы: 1

TSSTTV-ELXLDAF3

Бренд: Oster Страницы: 17

Бренд: GE Страницы: 3

Бренд: GE Страницы: 32

Бренд: Lamona Страницы: 32

Бренд: DonLim Страницы: 25

Бренд: Omega Страницы: 20

Бренд: Godrej Appliances Страницы: 204

Бренд: Newworld Страницы: 36

Бренд: Daewoo Страницы: 39

xcelerate XL-300

Бренд: Alto-Shaam Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды