LG LZ-H050GXH0 Скачать руководство пользователя страница 3

Страница: 3 / 33

Safety Precautions

Installation Manual

ENGLISH

Safety Precautions

To prevent injury to the user or other people and property damage, the following instructions
must be followed.

Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is
classified by the following indications.

CAUTION

This symbol indicates the possibility of injury or damage.

Installation

Do not use a defec-
tive or underrated cir-
cuit breaker. Use this
appliance on a dedi-
cated circuit.

• There is risk of fire or

electric shock.

For electrical work,
contact the dealer,
seller, a qualified
electrician, or an
Authorized Service
Center.

• Do not disassemble or

repair the product.
There is risk of fire or
electric shock.

Always ground the
product.

• There is risk of fire or

electric shock.

Install the panel and
the cover of control
box securely.

• There is risk of fire or

electric shock.

Always install a dedi-
cated circuit and
breaker.

• Improper wiring or

installation may cause
fire or electric shock

Use the correctly rated
breaker or fuse.

• There is risk of fire or

electric shock.

WARNING

Do not modify or
extend the power
cable.

• There is risk of fire or

electric shock.

Do not install,
remove, or re-install
the unit by yourself
(customer).

• There is risk of fire,

electric shock, explo-
sion, or injury.

Be cautious when
unpacking and
installing the prod-
uct.

• Sharp edges could

cause injury.

Содержание LZ-H050GXH0


































Результаты поиска

Содержание LZ-H050GXH0

Отзывы:

Похожие инструкции для LZ-H050GXH0

Бренды по названию

Популярные бренды

LG LZ-H050GXH0, Руководство по установке

Результаты поиска

Содержание LZ-H050GXH0

Отзывы:

Похожие инструкции для LZ-H050GXH0

Бренды по названию

Популярные бренды