LG LZ-H050GXH0 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 33

background image

Installation Manual

25

ENGLISH

Wiring Connection

Wiring for the Humidity Regulator (Locally Procured)

<LZ-H***GXH series only>

1. Pass into the electric parts box together with the power wire through the power wiring through-hole.
2. Remove the short-circuit wires (3 and 4) on the TB 2 terminal block and connect the wiring for the

humidity regulator.

3. Secure with cramping material together with the power wire.

Wiring specifications

Sheathed wire (should be complied with IEC60245 standard)

Size

0.75 - 1.25 mm

2

Length

MAX. 100 m

External contact specifications

Normally closed contact (Current tolerance 10 mA - 0.5 A)

• If using humidistat, install one per ventilation unit.

Controlling more than one ventilation unit with a single humidity controller may prevent normal
humidity operation and cause water leakage, etc.

CAUTION

«
...
23
24
25
26
27
...
»

Содержание LZ-H050GXH0


































Отзывы:

Нет отзывов

Похожие инструкции для LZ-H050GXH0

Бренд: Panasonic Страницы: 56

Бренд: Panasonic Страницы: 60

Бренд: Panasonic Страницы: 297

Бренд: Airwell Страницы: 55

Бренд: Lennox Страницы: 20

C*ED060A Series

Бренд: Unitary products group Страницы: 24

Бренд: WAGNER Страницы: 5

Бренд: Daikin Страницы: 29

Бренд: Bard Страницы: 59

Бренд: Kogan Страницы: 15

Бренд: Click Страницы: 16

Бренд: ALPATEC Страницы: 20

Бренд: Trane Страницы: 28

Бренд: Lennox Страницы: 8

Бренд: Carrier Страницы: 44

Бренд: NewAir Страницы: 14

23-23-0258N-013 s

Бренд: Fedders Страницы: 31

Бренд: Air Oasis Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды