LG LP073CD2A Скачать руководство пользователя | Manualshive

Страница: 25 / 51

background image

- 25 -

Copyright ©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes

LGE Internal Use Only

Perpendicular
20 A

Tandem
15 A

Large Tandem
30 A

208/230 volt receptacle configuration

CAUTION

1. Do not use an extension cord with this unit.
2. When the unit is in the OFF position, the power supply to the

electrical controls is still energized.

3. Disconnect the power to the unit before servicing

the unit.

4. Remove the power cord from the wall receptacle.
5. Remove or turn off the protective device (fuses or circuit breaker).

Wirings including installation of the receptacle must comply with the
NEC and local codes, local regulations.

FUSE- Use a time-delay fuse or circuit breaker. Refer to the nameplate

for proper power supply requirements.

3.3.1 ELECTRICAL DATA (FOR 208/230V MODEL)

3.3.2 ELECTRICAL SAFETY

IMPORTANT GROUNDING INSTRUCTIONS
The air conditioner has a three-prong grounding plug on its power supply cord which must be plugged into properly grounded
three-prong wall receptacle for your protection against possible shock hazard.
FUSE – Use a time-delay fuse or circuit breaker. Refer to the nameplate for proper power supply requirements.
208, 230, and 208/230 VOLT UNITS
These units are equipped with a three-prong grounding plug on the power supply cord which must be plugged into a matching
properly grounded three-prong wall receptacle for your protection against possible shock hazard. If such an outlet is not
present, one must be installed by a qualified electrician in accordance with the National Electrical Code and local codes and
ordinances.
NOTE: DO NOT USE AN EXTENSION CORD on 208, 230, and 208/230 Volt units.

3.3 ELECTRICAL REQUIREMENTS

«
...
23
24
25
26
27
...
»

Содержание LP073CD2A




















































Отзывы:

Нет отзывов

Похожие инструкции для LP073CD2A

Бренд: Danby Страницы: 28

Бренд: Danby Страницы: 13

Premiere DPAC9009

Бренд: Danby Страницы: 24

Бренд: Daikin Страницы: 38

Бренд: Hisense Страницы: 43

Бренд: Kroll Страницы: 28

Symphony Solo Series

Бренд: YMGI Страницы: 48

KACSE 012 TO 144 Series

Бренд: ThermoPlus Air Страницы: 2

PREFERRED 124ANS

Бренд: Bryant Страницы: 6

Бренд: York Страницы: 30

Бренд: Olimpia splendid Страницы: 52

Comfort 50VL-C 24

Бренд: Carrier Страницы: 6

Бренд: York Страницы: 16

DYNAPACK S Series

Бренд: Suburban Страницы: 22

V7KI-18WiFiR/U7RS-18

Бренд: INVENTOR Страницы: 144

Бренд: Napoleon Страницы: 40

Бренд: Lennox Страницы: 32

Бренд: Blueridge Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды