LG LP073CD2A Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 51

background image

- 32 -

Copyright ©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes

LGE Internal Use Only

Outdoor Drain Kit Installation

Before installing the wall sleeve louvered condenser grille, it
must be determined if the optional outdoor wall sleeve drain
kit is to be installed. The drain kit will allow the condensate
from the outdoor and indoor coils to be routed to a suitable
area. The drain kit can be installed so the condensate can be
drained from the right or left hand side of the wall sleeve. See
Figure 36. See local codes for proper condensate disposal.

To install the outdoor drain components proceed as follows:

1. Remove the rear enclosure panel and the sleeve stiffener.

These items may be removed from the inside of the
building.

2. The drain fitting can be installed on the left or right hand

side of the sleeve. (Illustration will be for a right hand
installation.) Insert the drain fitting in the opening of gasket
A and hole of Plate "B". Secure this assembly to the rear of
the sleeve with two sheet metal screws into holes G
provided in sleeve. See Figures 37 and 38.

3. Locate the other gasket A on the back of blank off plate C

and secure the assembly to the left rear of wall sleeve with
sheet metal screws provided. See Figure 39 for finished left
hand side installation.

If the unit chassis is to be installed right away, install the
condenser grille to wall sleeve with hardware provided. See
condenser grille installation instructions.

If the unit chassis will not be installed right away, replace the
rear enclosure panel in the wall sleeve. This will help protect
the inside of the building from weather damage.

If a subbase is used, be sure the right hand subbase cover is
removed before the chassis is installed in the sleeve. Slide
the chassis into the wall sleeve until the chassis flanges

contact the front edge of sleeve. Secure the chassis to the
wall sleeve on each side with screws provided.

Re-install the cabinet front.

See the following pages for installation instructions of indoor
drain kit.

1/2" DRAIN

FITTING

DRAIN FITTING

PLATE B

GASKETS A

MTG. SCREWS

BLANK-OFF

PLATE C

Figure 36 – Outdoor Drain Kit Installation

G

PLATE "B"

DRAIN FITTING

BLANK-OFF PLATE

SHEET METAL SCREWS

Figure 37

Figure 38

Figure 39

See Detail A

Sleeve overflow port

Do not close up this port

Gasket

MTG. Screws (2)

1/2" Outdoor Drain Fitting

Detail A

Cover

Plate

Wall Sleeve Bottom

(4) Mounting Screws

Gasket (2)

Blank-off Plate (2)

Figure 40

«
...
30
31
32
33
34
...
»

Содержание LP073CD2A




















































Отзывы:

Нет отзывов

Похожие инструкции для LP073CD2A

Бренд: Daikin Страницы: 20

Бренд: Daewoo Страницы: 14

Бренд: DAEWOO ELECTRONICS Страницы: 18

AIRPUR PAP 650V

Бренд: S&P Страницы: 13

Бренд: Daikin Страницы: 15

Бренд: Aktobis Страницы: 12

23-23-0259N-006 s

Бренд: Fedders Страницы: 28

NanoCaptur PU408 Series

Бренд: Rowenta Страницы: 83

Бренд: King Industrial Страницы: 6

ClimaPiu 8 HE HP

Бренд: Olimpia splendid Страницы: 37

Бренд: Coway Страницы: 124

Бренд: Salton Страницы: 11

Mini-M M2DYH Series

Бренд: M-system Страницы: 5

Бренд: EnviroAire Страницы: 3

Бренд: Daikin Страницы: 20

Бренд: Nortek Страницы: 16

Бренд: TriStar Страницы: 48

Бренд: Carrier Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды