LG L5UC728FA2 Скачать руководство пользователя страница 8

Страница: 8 / 60

Multi Type Air Conditioner

Installation of Indoor, Outdoor Unit

2. Outdoor unit

1. If an awning is built over the unit to prevent

direct sunlight or rain exposure, make sure
that heat radiation from the condenser is not
restricted.

2. Ensure that the spaces indicated by arrows

around front, back and side of the unit.

3. Do not place animals and plants in the path

of the warm air.

4. Take the air conditioner weight into account

and select a place where noise and vibration
are minimum.

5. Select a place so that the warm air and noise

from the air conditioner do not disturb
neighbors.

Rooftop Installations:

If the outdoor unit is installed on a roof
structure, be sure to level the unit. Ensure the
roof structure and anchoring method are
adequate for the unit location. Consult local
codes regarding rooftop mounting.

• There should not be any heat source or steam

near the unit.

• There should not be any obstacles to prevent

the air circulation.

• A place where air circulation in the room will

be good.

• A place where drainage can be easily

obtained.

• A place where noise prevention is taken into

consideration.

• Do not install the unit near the door way.

• Ensure the spaces indicated by arrows from

the wall, ceiling, or other obstacles.

• The indoor unit must keep the maintenance

space.

Unit:mm

Ceiling

Ceiling Board

20 or more

1500

or more

500 or

Floor

Ceiling Cassette Type

more than

75 cm

more than

25 cm

more than

25 cm

more than

25 cm

more than

75cm

more than

25cm

more than

25cm

Содержание L5UC728FA2





























































Результаты поиска

Содержание L5UC728FA2

Отзывы:

Похожие инструкции для L5UC728FA2

Бренды по названию

Популярные бренды

LG L5UC728FA2, Руководство по установке

Результаты поиска

Содержание L5UC728FA2

Отзывы:

Похожие инструкции для L5UC728FA2

Бренды по названию

Популярные бренды