LG L5UC728FA2 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 60

background image

24

Multi Type Air Conditioner

Installation of Indoor, Outdoor Unit

■

WIRED REMOTE CONTROL INSTALLATION (PQRCUSA0)

1. Disassemble the remote controller from

the installation board.

•

Use the driver as shown in the right picture
and insert it into the hole with the arrow. And
then you pull the driver in the front direction,
the remote controller will be separated.

2. Connect the remote controller cable to

the wired remote controller installation
board as shown in the right picture.

3. After fixing the cable to the guide slot,

attach the wired remote controller
installation board at the desired location.

• Before fixing the remote controller cable to

the guide slot, remove any clogged part of
the case in the direction to install before the
installation.

4. After locating the wired remote

controller installation board at the
desired location, screw the unit firmly.
(When there is a buried box, install the
wired remote controller board to fit the
buried box.)

• Use the screw provided.

5. After fixing the top part of the remote

controller to the installation board as
shown in beside picture, press the
bottom part to assemble the controller
to it’s board.

12V

Red wire

SIG

Yellow wire

GND

Black wire

❊

The remote controller cable is connected as factory default.

12V SIG GND

Red
Yellow
Black

Remote Controller
Cable

Guide slot

Fixate the remote
controller cable
to the guide slot.

Use the screws
for fixate the unit
firmly on the wall.

Installation board

<Front side of

installation board>

<Rear side of

installation board>

Top

Bottom

Wall

Side

Wall

Side

Wall

Side

«
...
22
23
24
25
26
...
»

Содержание L5UC728FA2





























































Отзывы:

Нет отзывов

Похожие инструкции для L5UC728FA2

Бренд: Zanotti Страницы: 94

Бренд: TCL Страницы: 34

Nexya S4 E Series

Бренд: Olimpia splendid Страницы: 336

Бренд: Technibel Страницы: 24

Бренд: Gree Страницы: 37

Бренд: Gree Страницы: 31

Бренд: Danby Страницы: 56

CCA3U-09HRFN1-MC

Бренд: MDV Страницы: 213

Enviro-Therm SCE-AC2550B460V

Бренд: SCE Страницы: 17

Бренд: Nordyne Страницы: 20

Бренд: Industrial Climate Engineering Страницы: 26

digitemp 91154AA WHP 245

Бренд: Xpelair Страницы: 29

Бренд: clair Страницы: 8

Бренд: Lennox Страницы: 8

Бренд: Daikin Страницы: 15

Бренд: Daikin Страницы: 28

Бренд: Daikin Страницы: 40

Бренд: Daikin Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды