LG L5UC728FA2 Скачать руководство пользователя страница 4

Страница: 4 / 60

Multi Type Air Conditioner

Safety Precautions

To prevent injury to the user or other people and property damage, the following instructions
must be followed.

■

Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness
is classified by the following indications.

■

Meanings of symbols used in this manual are as shown below.

WARNING

CAUTION

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage.

Be sure not to do.

Be sure to follow the instruction.

Safety Precautions

WARNING

■

Installation

Install the panel and the cover of
control box securely.

• There is risk of fire or

electric shock.

Always install a dedicated
circuit and breaker.

• Improper wiring or

installation may cause fire or
electric shock

Use the correctly rated breaker
or fuse.

• There is risk of fire or

electric shock.

Do not use a defective or
underrated circuit breaker. Use
this appliance on a dedicated
circuit.

• There is risk of fire or

electric shock.

For electrical work, contact the
dealer, seller, a qualified
electrician, or an Authorized
Service Center.

• Do not disassemble or repair

the product. There is risk of
fire or electric shock.

Always ground the product.

• There is risk of fire or

electric shock.

Содержание L5UC728FA2





























































Результаты поиска

Содержание L5UC728FA2

Отзывы:

Похожие инструкции для L5UC728FA2

Бренды по названию

Популярные бренды

LG L5UC728FA2, Руководство по установке

Результаты поиска

Содержание L5UC728FA2

Отзывы:

Похожие инструкции для L5UC728FA2

Бренды по названию

Популярные бренды