LG CodeZero A9 Series Скачать руководство пользователя страница 95

Страница: 95 / 104

-95-

Only training and service purposes

Cleaning function operation and error modes

Failure

Cause of failure

How to check

Measures

No power supply

The Main PCB is faulty.

Check if the DC voltage at both ends of the Main PCB C118 is 5V.

Replace the Main PCB.

Main PCB Wire disconnection

Using a tester, check if the power cord is disconnected.

Replace the power cord.

The Display PCB is faulty.

Check if the DC voltage between No. 1 pin and No. 6 pin of the

Display No. CN39 Connector is 5V.

Replace the Display PCB.

Display PCB Wire disconnection

Check for disconnection using a tester (Main CN30 and Display CN39

connection line)

Replace the Top Cover Assembly or replace

the Harness.

Connector fastened incorrectly

Check the fastening and assembly status of the Main PCBA

Connector (CN22, CN30).

Reassemble or replace the Connector.

The suction motor

operation is faulty.

The Motor unit is faulty.

Using a tester, check if the motor coil is disconnected.

Replace the Chamber Assembly.

Motor Wire disconnection

Using a tester, check if it is disconnected (CN24, CN25- suction motor

connection line).

Replace the Motor Wire.

Connector fastened incorrectly

Check the connector fastening and assembly status (CN24, CN25).

Reassemble or replace the Connector.

The Main PCB is faulty.

Using a tester, check if the Triac (U23, U22) and/or the resistance

(R159, R158) are damaged.

Check the voltage of the PCB Motor output terminal (CN27) when the

suction operation is carried out with CN27 housings connected.

Replace the Main PCB.

A9S mount holder
operation failure

The sealing motor is faulty (Synchronous

motor).

Using a tester, check if the Motor coil is disconnected.

Replace the Duct Assembly.

The nozzle opening and closing hole motor

is faulty (Synchronous motor).
The dust canister cover hook release unit

motor is faulty (DC motor).
Motor Wire disconnection

Using a tester, check if it is disconnected.

Replace the Duct Assembly or the Harness.

Motor terminal fastened incorrectly

Check the terminal fastening and assembly status.

Reassemble or replace the Terminal.

Содержание CodeZero A9 Series



































































Результаты поиска

Содержание CodeZero A9 Series

Отзывы:

Похожие инструкции для CodeZero A9 Series

Бренды по названию

Популярные бренды

LG CodeZero A9 Series, Руководство по обслуживанию

Результаты поиска

Содержание CodeZero A9 Series

Отзывы:

Похожие инструкции для CodeZero A9 Series

Бренды по названию

Популярные бренды